Technical Data; Before Starting The Equipment - EINHELL CC-PO 1100/1 E Instructions D'origine

•
Reaching into the wheel while it is still rotating
(injuries through cutting)
•
Catapulting of parts of the wheel (injuries
through cutting or bruising)
•
Catapulting of parts of the material being pro-
cessed (injuries through cutting or bruising)
•
Risk of fire from flying sparks
•
Damage to hearing if the compulsory hearing
protection is not used (hearing loss)
•
Inhalation of abrasive particles from the mate-
rial and wheel
•
Electric shock upon contact with non-insula-
ted electrical parts
If the instructions listed in the operating instruc-
tions are not adhered to, improper handling of the
equipment may result in other residual risks

4. Technical data

Voltage: .......................................... 230 V ~ 50 Hz
Power rating: ............................................ 1100 W
Speed n: .....................................1000-3500 min
Polishing / sanding disk diameter: .......... 180 mm
Connection thread: ....................................... M14
Protection class: ............................................ II/
Weight: .......................................................2.2 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ........................ 86 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 97 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Operating mode: Sanding with sanding paper
Vibration emission value a
K uncertainty = 1.5 m/s
Operating mode: Polishing
Vibration emission value a
K uncertainty = 1.5 m/s
Anl_CC_PO_1100_1_E_SPK1.indb 16 Anl_CC_PO_1100_1_E_SPK1.indb 16
-1
= 13.47 m/s
2
h,DS
2
= 11.55 m/s
2
h,P
2
- 16 -
GB
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Assembly (Fig. 4-7)
Important! Pull out the mains power plug before
starting the assembly work.
05.04.16 08:28 05.04.16 08:28