Technical Data - Scheppach 88001951 Traduction Des Instructions D'origine

During non-use of the electric tool or prior to
–
maintenance and when replacing tools such
as saw blades, bits, milling heads.
Do not leave a tool key inserted
16
Before switching on, make sure that keys and
–
adjusting tools are removed.
Avoid inadvertent starting
17
Make sure that the switch is switched off
–
when plugging the plug into an outlet.
Use extension cables for outdoors
18
Only use approved and appropriately identi-
–
fied extension cables for use outdoors.
Only use cable reels in the unrolled state.
–
Remain attentive
19
Pay attention to what you are doing. Remain
–
sensible when working. Do not use the elec-
tric tool when you are distracted.
Check the electric tool for potential damage
20
Protective devices and other parts must be
–
carefully inspected to ensure that they are
fault-free and function as intended prior to
continued use of the electric tool.
Check whether the moving parts function
–
faultlessly and do not jam or whether parts
are damaged. All parts must be correctly
mounted and all conditions must be fulfilled to
ensure fault-free operation of the electric tool.
The moving protective hood may not be fixed
–
in the open position.
Damaged protective devices and parts must
–
be properly repaired or replaced by a recog-
nised workshop, insofar as nothing different is
specified in the operating manual.
Damaged switches must be replaced at a
–
customer service workshop.
Do not use any faulty or damaged connection
–
cables.
Do not use any electric tool on which the
–
switch cannot be switched on and off.
ATTENTION!
21
Exercise elevated caution for double mitre
–
cuts.
ATTENTION!
22
The use of other insertion tools and other ac-
–
cessories can entail a risk of injury.
Have your electric tool repaired by a qualified
23
electrician
This electric tool conforms to the applicable
–
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
ADDITIONAL SAFETY RULES FOR SCROLL
SAWS
• This scroll saw is intended for use in dry conditions,
and for indoor use only.
• Do not cut pieces of material too small to hold by
hand outside the blade guard.
• Avoid awkward hand positions where a sudden slip
could cause a hand to move into the blade.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Always use the blade guard to avoid possible injury
due to blade breakage.
• Never leave the scroll saw work area with the
power 01), or before the machine has come to a
complete stop.
• Do not perform layout, assembly or set up work
on the table while the cutting tool is in operation.
• Never turn your scroll saw on before clearing
the table of all objects: (tools, scraps of wood,
etc) except for the workpiece and related feed or
support devices for the operation planned.
Remaining hazards
The machine has been built using modern tech-
nology in accor dance with recognized safety
rules. Some remaining hazards, how ever, may
still exist.
• Long hair and loose clothing can be hazardous
when the work piece is rotating. Wear personal
protective gear such as a hair net and tight fitting
work clothes.
• Saw dust and wood chips can be hazardous. Wear
per so nal protective gear such as safety goggles
and a dust mask.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimized by following
the instructions in „Safety Precautions", „Proper
Use" and in the entire operating manual.
• Do not force the machine unnecessarily: excessive
cutt ing pressure may lead to rapid deterioration of
the blade and a decrease in performance in terms
of finish and cutting precision.
• Avoid accidental starts: do not press the start
button while inserting the plug into the socket.
Keep this safety information in a safe place.

6. Technical data

deco-flex
Extent of delivery
Technical data
Dimensions
L x W x H mm
Bench size mm
Saw blade
length mm
Cutting height
max. mm
Working depth mm
Lifting
movement mm
Lifting speed 1/min
(electronical)
GB
DE FR
Scroll saw
Flexible Wave
Accessories kit
Operating instructions
630 x 320 x 380
ø 255 x 415
127
50
405
20
550 – 1600
19 / 40