Functional Description; Removing/Inserting The Battery - Milwaukee M18 FUEL Manuel De L'utilisateur

FUNCTIONAL DESCRIPTION

12
11
10
9
1. Hook
2. Trigger
3. Handle
4. Power/Actuation
selection
5. Nail slot
6. LED
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Installing/Removing Fastener Strips
(Cat. No. 2741-20, 2742-20, 2743-20)
Always remove battery pack before
WARNING
changing or removing fasteners.
Always wear safety goggles or glasses with side
shields.
Keep fingers clear of fastener track of magazine.
Pusher could pinch fingers, causing injury.
To install fastener strips:
1. Remove battery pack.
2. WARNING! Always point the tool away from yourself
and others when installing fasteners. Failure to do
so could result in injury.
1
4
3
2
6
7
8
7. Magazine
8. Pusher
9. Pusher release
button
10. Workpiece contact
11. Depth adjustment
12. Jam latch
3. Slide the fastener strip into the nail slot and down
toward the front of the tool. Be sure the point of the
fasteners is pointed downward. WARNING! Use only
recommended fasteners of the correct size, length,
collation angle and head type as indicated on the
tool's nameplate. Other fasteners could result in tool
malfunction, leading to injury.
4. Press and hold the pusher release button and slide
the pusher back past the end of the fastener strips.
5. Continue to hold the pusher, but release the button.
Slowly slide the pusher forward until it rests against
the fastener strip.
To remove fastener strips:
1. Remove battery pack.
2. WARNING! Always point the tool away from yourself
and others when installing fasteners. Failure to do
so could result in injury.
3. Press and hold the pusher release button and slide
5
the pusher towards the front of the tool. Release the
pusher.
4. Slide the nails back and out of the nail slot.
Installing/Removing Fastener Strips
WARNING
9
Always wear safety goggles or glasses with side
shields.
To install fastener strips:
1. Remove battery pack.
2. WARNING! Always point the tool away from yourself
and others when installing fasteners. Failure to do
so could result in injury.
3. Press the pusher release button and slide the
magazine open. Place the tip of the fasteners into the
bottom slot of the magazine; then lay the fasteners
flat against the magazine. The heads must fit into
the grooves. WARNING! Use only recommended
fasteners of the correct size, length, collation angle
and head type as indicated on the tool's nameplate.
Other fasteners could result in tool malfunction, lead-
ing to injury.
4. Slide the magazine closed.
To remove fastener strips:
1. Remove battery pack.
2. WARNING! Always point the tool away from yourself
and others when installing fasteners. Failure to do
so could result in injury.
3. Press the pusher release button and slide the maga-
zine open.
4. Remove the fasteners.
WARNING
with side shields. The operator and other people
in the work area must wear eye protection in ac-
cordance with ANSI Z87.1. Eye protection does not
fit all operators in the same way. Make sure the eye
protection chosen has side shields or provides
protection from flying debris both from the front
and sides. The employer is responsible for enforc-
ing the use of eye protection by the operator and
other people in the work area. When required, wear
head protection in accordance with ANSI Z89.1.
To reduce the risk of injury to yourself and others,
test the tool before beginning work each day ac-
cording to the "Required Daily Testing" section.
4
(Cat. No. 2740-20)
Always remove battery pack before
changing or removing fasteners.
OPERATION
To reduce the risk of injury, always
wear safety goggles or glasses