Safety Instructions - Ryobi ETMS-1426 Manuel D'utilisation

GB
F D

SAFETY INSTRUCTIONS

Please read this manual carefully and pay attention to the
information provided. Use this manual to familiarize
yourself with the machine, its correct use and safety
regulations.
IMPORTANT
Whenever you use electric tools it is imperative to
take basic safety precautions in order to reduce
the risk of fire, electric shock and personal injury.
Essential safety precautions include:
Follow all these instructions before and while you are
■
working with the saw.
Keep these instructions in a safe place.
■
Avoid body contact with earthed components.
■
When equipment is not being used it should be kept
■
in a dry, closed place out of children's reach.
You will work better and more safely if you keep your
■
tools sharp and clean.
Check the power cable regularly and have it replaced
■
by an authorized specialist at the first sign of any
damage.
Check your extension cables regularly and replace
■
them if damaged.
When working outdoors, use only extension cables
■
that are approved for outdoor use and which are
marked accordingly.
Concentrate on what you are doing. Take a sensible
■
attitude to your work. Never use the tool when you
are tired.
Never use a tool with a switch that cannot be turned
■
on and off.
CAUTION
The use of plug-in tools and accessories other
than those intended may put you at risk of injury.
The machine is equipped with a safety switch (4)
■
to prevent it being switched on again accidentally
after a power failure (in table saw mode).
Never use the saw to cut round timber.
■
Check the power cable. Never use a faulty or
■
damaged power cable.
Do not use the cable to pull the plug out of the
■
socket-outlet. Protect the cable from heat, oil and
sharp edges.
We recommend that you wear non-slip shoes when
■
working outdoors.
E I P NL S DK N FIN
English
Keep long hair in a hair net.
■
Avoid abnormal working postures.
■
An untidy work area may result in accidents.
■
Do not allow other persons, particularly children,
■
to touch the tool or the power cable. Keep them away
from your workplace.
The splitter is an important safety device. Not only
■
does it guide the workpiece, it also prevents the kerf
closing behind the blade so that there is no kickback
from the workpiece. Note the thickness of the splitter.
The splitter should never be thinner than the saw
blade body or thicker than the width of its kerf.
Upper saw blade guard (17) has to be lowered over
■
the workpiece for each cut.
Be sure to use a push stick when slitting narrow
■
workpieces smaller than 120 mm in width or a push
block when slitting narrow workpieces smaller than
30 mm in width.
IMPORTANT
Never use this saw to make plunge cuts.
Always stand to the side of the saw blade when
■
working with the mitre saw.
Make sure that off-cuts do not catch on the saw blade
■
crown or they may be catapulted into the surrounding
area.
If the sawing gap is worn, replace the table insert.
■
Pull out the power plug!
To prevent injury from flying sawdust and chips,
■
use the saw only with a suitable vacuum extraction
system or standard industrial vacuum cleaner.
Always pull the plug out of the power socket before
■
adjusting or servicing the machine.
Give these safety regulations to all persons who work
■
on the machine.
Do not use this saw to cut fire wood.
■
CAUTION
Hands and fingers may be injured on the rotating
saw blade.
Before you use the machine for the first time, check
■
that the voltage marked on the rating plate is the
same as your mains voltage.
If you need to use an extension cable, make sure its
■
conductor cross-section is big enough for the saw's
power consumption. Minimum cross-section: 1.0 mm
If you use a cable reel, the complete cable has to be
■
pulled off the reel.
Never carry the saw by its cable.
■
9
GR H CZ RUS RO PL
2
.