Cleaning, Maintenance And Ordering Of Spare Parts; Ordering Replacement Parts - Scheppach HMS850 Traduction Des Instructions D'origine

12.2.3 Thicknessing mode (Figure 11/13/17)
Attention! Watch out the right mounting of the chip
extractor (point 12.2.2).
• Connect the mains plug to the mains lead.
• Press the green button "I" to start the plane.
• Place a workpiece on the thicknessing table (20).
• Guide the workpiece towards the feed table (13). (Pay at-
tention to the direction of the arrow, which also symbolizes
the working direction.)
• When you have finished work, switch off the machine. To do
this, press the red button "0". Then disconnect the machine
from the mains supply.
• Remove the chips and dust from the thicknessing table (20)
and knife block (23) after the machine has reached a com-
plete standstill.
• Use the pull-out workpiece support (10) for long workpieces.
13. Cleaning, maintenance and ordering
of spare parts
13.1 General maintenance measures
Wipe chips and dust off the machine from time to time using a
cloth. In order to extend the service life of the tool, oil the rotary
parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products.
m Warning!
Before cleaning ~ , adjustment ~ , maintenance ~ or repair work,
disconnect the power cord from the main power supply!
13.2 Cleaning
• Keep all safety devices, air vents and the motor housing free
of dirt and dust as far as possible. Wipe the equipment with
a clean cloth or blow it with compressed air at low pressure.
• We recommend that you clean the device immediately each
time you have finished using it.
• Clean the equipment regularly with a moist cloth and some
soft soap. Do not use cleaning agents or solvents; these
could attack the plastic parts of the equipment. Ensure that
no water can seep into the device. The ingress of water into
an electric tool increases the risk of an electric shock.
• The sawdust ejection and/or dust exhauster should be
cleaned at regular intervals.
• Never spray water on the machine!
13.2 Maintenance (Figure 1/15)
If maintenance work is required, also observe the regular main-
tenance periods under "17. Troubleshooting".
13.2.1 Machine
Lubricate the following parts periodically after around 10
hours of service:
• Bearings for the feed/discharge rollers and anti-kick claws
(24)
• Bearings on the belt roller and pulley
• Grub screws to adjust the height of the thicknessing table
(20)
Use only dry lubricant.
The feed table (13), planing table (14), thicknessing table
(20), feed/discharge rollers and anti-kick claws (24) must be
kept free of resin at all times. Soiled feed/discharge rollers or
anti-kick claws (24) must be cleaned without delay. To prevent
the motor overheating, the dust that accumulates in the ventila-
tion openings must be removed at regular intervals. Improve the
smooth running of the tables by applying lubricant at regular
intervals.
13.2.2 Cutting tool
Resin must be cleaned off the knife (21), latch (22) and knife
block (23) at regular intervals. Clean these components with
an appropriate resin remover.
13.2.3 Changing the knives (Figure 17/18)
m Important!
Always pull the mains plug before changing the knives.
• Remove the parallel stop following the instructions in 11.1
in reverse.
• Pull the planing knife cover (12) forwards as far as possible
so that the entire knife block (23) is exposed.
• Undo the clamp screws (A) by turning them clockwise using
the open-ended spanner (17) supplied.
• Turn the knife block (23) so that the latch (22) can be pulled
out with the knife (21).
• Clean all the relevant parts and the knife slots in the knife
block (23).
• Fit the latch (22) with the new knife (21) and align them with
the side of the knife block.
• Place the blade adjustment block (15), as shown in Figure
18, on the knife block. Make sure that the knife (21) touches
both sides of the blade adjustment block (15).
• Tighten the clamp screws (A) using the openended spanner
(17) supplied.
• Return the planing knife cover (12) to its original position so
that the knife (21) is covered.
m Important!
Only use knives which are recommended by the manufacturer
for this equipment. If you use other knives there is a risk of inju-
ries due to lack of control.
Avoid over-tightening and the possibility of the thread becom-
ing detached. If the latch (22) or the screws have worn out
threads they must be immediately replaced.

13.3 Ordering replacement parts:

Please quote the following data when ordering replacement
parts;
• Type of machine
• Article number of the machine
• Identification number of the machine
• Replacement part number of the part required
Repairs and works specified in these Instructions may only be
performed by qualified authorised staff.
Service information
Please note that the following parts of this product are sub-
ject to normal or natural wear and that the following parts are
therefore also required for use as consumables.
GB 23