Special Safety Instructions - Scheppach HMS850 Traduction Des Instructions D'origine

9. Use protective equipment
- Use safety glasses.
- Use face or dust mask if working operations create
dust.
10. Connect dust extraction equipment
- lf the tool is provided for the connection of dust extrac-
tion and collecting equipment, ensure these are con-
nected and properly used.
11. Do not abuse the cord
- Never yank the cord to disconnect it from the socket.
Keep the cord away from heat, oil and sharp edges.
12. Secure work
- Where possible use clamps or a vice to hold the work.
lt is safer than using your hand.
13. Do not overreach
- Keep proper footing and balance at all times.
14. Maintain tools with care
- Keep cutting tools sharp and clean for better and safer
performance.
- Follow instruction for lubricating and changing acces-
sories.
- lnspect tool cords periodically and if damaged have
them repaired by an authorized service facility.
- lnspect extension cords periodically and replace if
damaged.
- Keep handles dry, clean and free from oil and grease.
15. Disconnect tools
- When not in use, before servicing and when changing
accessories such as blades, bits and cutters, discon-
nect tools from the power supply.
16. Remove adjusting keys and wrenches
- Form the habit of checking to see that keys and adjust-
ing wrenches are removed from the tool before turning
it on.
17. Avoid unintentional starting
- Ensure switch is in "off' position when plugging in.
18. Use outdoor extension leads
- When the tool is used outdoors, use only extension
cords intended for outdoor use and so marked.
19. Stay alert
- Watch what you are doing, use common sense and do
not operate the tool when you are tired.
20. Check damaged parts
- Before further use of tool, it should be carefully checked
to determine that it will operate properly and perform
its intended function.
- Check for alignment of moving parts, binding of mov-
ing parts, breakage of parts, mounting and any other
conditions that may affect its operation.
- A guard or other part that is damaged should be
properly repaired or replaced by an authorized ser-
vice centre unless otherwise indicated in this instruction
manual.
- Have defective switches replaced by an authorized
service centre.
- Do not use the tool if the switch does not turn it on
and off.
21. WARNING!
- The use of any accessory or attachment other than one
recommended in this instruction manual may present a
risk of personal injury.
22. Have your tool repaired by a qualified person
- This electric tool complies with the relevant safety
rules. Repairs should only be carried out by qualified
persons using original spare parts, otherwise this may
result in considerable danger to the user.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appli-
ance by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.

Special safety instructions

• If the planer shaft blocked when working by excessive feed
force or clamping the work piece, turn off the device and dis-
connect it from the mains plug. Remove the workpiece and
make sure that the planer shaft runs freely. Turn the power
on, and run the operation again with reduced feed force.
• Do not use blunt knives. Risk of kick-back.
• The cutter block must be fully covered.
• Use a push stick to plane any short workpieces.
• Take additional safety precautions if you are planing any
narrow workpieces. It may be necessary to use lateral pres-
sure equipment and springloaded covers to ensure that you
can work in safety.
• The machine is not suitable for cutting rebates.
• The anti-kick safeguard and the infeed roller must be inspect-
ed at regular intervals.
• Machines fitted with a sawdust extractor and extractor
hoods must be connected to the devices concerned. The
type of material used can have a negative influence on the
dust generated.
• The machine is designed exclusively for the cutting of wood
and similar materials.
• The knife must be replaced immediately once it becomes
worn down by 5%.
• If a push stick is not used there may be a risk of serious
danger. The push stick should always be kept at the machine
when not used.
• There is a greater risk of danger when small workpieces are
fed in by hand. Always observe the manufacturer's instruc-
tions on the use of the push stick.
• If the safety covers, infeed table or mesh are incorrectly
aligned they could lead to uncontrollable situations.
• Damaged or soiled workpieces may cause a risk of danger.
Never use metal parts in the machine or any materials which
can fracture or shatter. Risk of injury!
• To cut long workpieces, always place them on a mobile ta-
ble or similar type of supporting equipment. Otherwise there
is a risk that you may lose control over the workpiece.
• The machine is only suitable for planing and thicknessing.
• Wear suitable protective clothing when working with the machine:
- ear protection to prevent damage to your ears,
- a breathing mask to avoid the risk of inhaling hazard-
ous particles of dust,
- safety gloves to avoid injuries from sharp edges or
knives,
- safety goggles to avoid eye injuries from flying parts.
GB 19