Laser Safety; Intended Use; Environmental Protection - Ryobi EMS216L Traduction Des Instructions Originales

carried out by authorised service agents.
■ Always use the protective shields on the machine.
■ Do not clamp the protective swing guard.
■ Do not use saw blades which are damaged or deformed.
■ Replace the table insert when worn.
■ Do not use saw blades not corresponding to the key
data given in these instructions for use.
■ The protective cover should only open when the
machine is lowered to the workpiece.
■ Do not use saw blades made of high-speed steel.
■ Any faults with the machine, including any related to
the safeguard or the saw blades, must be reported to
the persons in charge of safety as soon as the faults
are discovered.
■ It is necessary to select a saw blade which is suitable
for the material being cut.
■ Never use the mitre saw to cut materials other than
those specified in the instruction manual.
■ The handle lock must always be engaged when
transporting the mitre saw.
■ Only use the saw with guards in good working order
and properly maintained, and in position.
■ Keep the floor area free of loose material e.g. chips and
cut-offs.
■ Only use saw blades which have been properly
sharpened. It is essential to adhere to the maximum
speed specified on the saw blade.
■ Do not use any flanges other than those supplied or
indicated in the instruction manual to secure the saw
blade.
■ Refrain from removing any cut-offs or other parts of the
workpiece from the cutting area whilst the machine is
running and the saw head is not in the rest position.
■ Ensure that the machine is always stable and secure
(e.g. fixed to a bench).
■ Long workpieces must be adequately supported.
■ Do not use cracked or distorted saw blades.
■ Before using the tool please read the instructions. If
possible have the tool demonstrated.
■ The dust produced when using this tool may be harmful
to health. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust
thoroughly, e.g. with a vacuum cleaner.
■ Stock having a round or irregular cross section (such
as firewood) must not be cut, as it cannot be securely
held during cutting. When sawing thin stock layered on
edge, a suitable auxiliary fence must be used for firm
support.
■ The unit should be connected to a circuit protection
device (fuse or circuit breaker).
■ Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
2
■ Take care when trenching.
■ Always use blades with correct size and shape of
arbour holes. Blades that do not match the mounting
hardware of the saw will run eccentrically, causing loss
of control.
■ Use only blades specified in this manual, complying
with EN 847-1.

LASER SAFETY

■ Do not stare into beam during operation.
■ Do not project the laser beam directly into the eyes of
others. Serious eye injury could result.
■ Do not place the laser in a position that may cause
anyone to stare into the laser beam intentionally or
unintentionally.
■ Do not use optical tools to view the laser beam.
■ Do not operate the laser around children or allow
children to operate the laser.
■ Do not attempt to repair the laser device by yourself.
■ Do not attempt to change any parts of the laser device
by yourself.
■ Any repairs must only be carried out by the laser
manufacturer or authorized service agent.
■ Do not replace the laser with a different type.

INTENDED USE

■ The mitre saw can be used for sawing solid wood,
bonded wood, glued veneer, materials similar to wood,
and plastics.
■ Do not use this product in any other way as stated for
normal use.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing
of as waste. The machine, accessories
and packaging should be sorted for
environmental-friendly recycling.
SYMBOL
Safety alert
CE conformity
Conformance to technical regulations
English