Introduction; Device Description; Scope Of Delivery - Scheppach 5806801903 Traduction De La Notice Originale

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope you have a lot of fun and success using your
new machine.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• improper handling,
• noncompliance of the operating instructions,
• repairs by third parties, not by authorized service
technicians,
• installation and replacement of non-original spare
parts,
• non-intended use,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regulations
and VDE regulations 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operating
instructions contain important information on how to
operate the machine safely, professionally and eco-
nomically, how to avoid danger, costly repairs, reduce
downtimes and how to increase reliability and service
life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions package
with the machine at all times and store it in a plastic
cover to protect it from dirt and moisture. Read the
instruction manual each time before operating the ma-
chine and carefully follow its information. The machine
can only be operated by persons who were instructed
concerning the operation of the machine and who are
informed about the associated dangers. The minimum
age requirement must be complied with. In addition to
the safety requirements in these operating instructions
and your country's applicable regulations, you should
observe the generally recognized technical rules con-
cerning the operation of woodworking machines.
We cannot accept any liability for damage or accidents
which arise due to a failure to follow these instructions
and the safety instructions.
22 / 60
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

2. Device description

1. Base plate
2. Pillar
3. Fixing screw
4. Toothed rack pillar
5. crank handle for drilling table
6. clamping handle (height adjustment)
7. Drilling table
8. Ring
9. Depth stop
10. Adjusting the spindle retaining spring
11. Emergency stop
12. On-Off switch
13. On-Off switch Laser
14. Drill chuck protection
15. Hood belt guard
16. Motor
17. Grips
18. Crank holder
19. Drilling chuck
20. Grub screw (Ring)
21. Grub screw (Machine head)
22. Phillips screw (Drill chuck protection)
23. Lock nut (angular play)
24. Adjusting screw (angular play)
25. Inclination display
26. Hexagon screw (90° fixation)
27. clamping nut (Angle adjustment)
28. Phillips screw (Hood belt guard)
29. Wing screws (belt tension)
30. Knurled nut (Depth stop)
31. Lower stop
32. Bench vise
A Drill chuck
B Allen key SW3
C Allen key SW4

3. Scope of delivery

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
m Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic bags,
film and small parts! There is a risk of swallowing and
suffocation!