Assembly And Adjustments; Led Worklight; Variable Speed Trigger; Lock-Off Button - Dewalt Dcgg581 Manuel D'instructions

RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
LED Worklight (Fig. C, D)

CAUTION: Do not stare into the LED. Serious eye injury
could result.
When the tool is activated by pressing the variable speed
trigger switch 1 , the LED worklight
turn on. The LED worklight will turn off 60 seconds after the
variable speed trigger switch has been released.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Variable Speed Trigger Switch and Lock-Off Button
(Fig. A, D)
Your grease gun is equipped with a lock-off button
The lock-off button has a locked or unlocked icon at
2
either end to indicate if the variable speed trigger switch
locked or unlocked.
1. To lock the variable speed trigger switch
lock-off button from the locked icon end as shown in
Fig. D.
nOTE: Always lock the variable speed trigger switch
carrying or storing the tool to eliminate unintentional starting.
2. To unlock the variable speed trigger switch
lock-off button 2 from the unlocked icon end as shown in
Fig. D.
3. Squeeze the variable speed trigger switch
motor ON.
4. Releasing the variable speed trigger switch turns the
motor OFF.
nOTE: The variable speed trigger switch will give you added
versatility. The further the trigger is depressed the higher
the output of grease.

WARNING: This tool has no provision to lock the switch
in the ON position, and should never be locked ON by any
other means.
PSI....................... pounds per square
inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation–
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
..................... do not expose to
rain
..................... hot surface
4 will automatically
2 .
1
1 , press the
when
1
, press the
1
1 to turn the
Pressure Relief Valve (Fig. E)
The pressure relief valve
pressure above 10000 PSI (690 bar). Grease coming out
of the pressure relief valve indicates a clog in the fitting,
line or bearing. Any of these conditions must be corrected
before proceeding.

WARNING: The grease gun may generate high
pressure. Do not remove or tamper with the pressure
relief valve. Serious injury may occur.
Installing a Grease Cartridge (Fig. A, E, F)
1. Pull the grease tube handle
then secure the grease tube rod
slot by moving the rod to the side. Ensure the rod is
14
placed securely in the slot to prevent it from disengaging.
2. Unscrew the grease tube assembly
grease gun.
3. Remove the plastic cap from the grease cartridge, then
insert the cartridge, open end first, into the grease tube
4. Remove the seal from the other end of the
grease cartridge.
5. Thread the grease tube assembly
grease gun and screw it in securely.
6. Release the grease tube rod
slot and slowly press it back into the tube.
14
7. Use the purge valve (
that may be trapped in the cartridge. Refer to Purging
Air Pockets.
iMPORTAnT: The grease gun will lose its prime if there are
air pockets in the lubricant.
Removing Empty Grease Cartridge (Fig. A, F)
1. Pull the grease tube handle
then secure the grease tube rod
slot 14 by moving the rod to the side. Ensure the rod is
placed securely in the slot to prevent it from disengaging.
2. Unscrew the grease tube assembly
gun and remove.
3. Gently release the grease tube handle
empty cartridge from the grease tube.
is Filling the Grease Gun from a Bulk Container
(Fig. A, E–I)
Preparing the Grease Gun for Suction and
Filler Pump Filling (Fig. A, F, G)
nOTE: Be sure the grease gun is empty of grease before
beginning this process.
1. Unscrew the grease tube
assembly 13 .
2. Unscrew the grease tube cap
and pull out the grease tube rod
3. Using your thumb and forefinger, flip the rubber seal
from the rear to the front. Refer to Fig. G.
nOTE: The seal resembles a cup, which should open toward
the motor housing
and filler pump filling.
4. Reinsert the grease tube rod
tube .
9
23 is set at the factory to relieve
11 out as far as it will go,
12 into the retaining
from the
13
13 back into the
12 from the retaining
24 , Fig. E) to bleed off any air
11 out as far as it will go,
12 into the retaining
13 from the grease
11
from the grease tube
9
10 from the grease tube
12 .
5 (Fig. A) when prepared for suction
12 back into the grease
English
.
9
to expel the
9 ,
28
7