Additional Safety Information - Dewalt Dcgg581 Manuel D'instructions

English
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with another
battery pack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may create a
risk of injury and fire.
c ) When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
d ) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the battery may cause
irritation or burns.
e ) Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or risk of injury.
f ) Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 265 °F (130 °C) may cause explosion.
g ) Follow all charging instructions and do not charge
the battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire.
6) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b ) Never service damaged battery packs. Service of
battery packs should only be performed by the manufacturer
or authorized service providers.
Additional Specific Safety Rules for Grease Guns
• Parts of the tool or the hose assembly can break or
rupture due to high pressure. Risk of serious injury
may occur. Before using, always inspect the tool and hose
assembly for damage or wear. Never use if any part of the tool
is damaged or worn.
• Use only D WALT-approved flexible hoses. Hold the
E
hose only by the flexible hose safety spring guard to avoid
personal serious injury.
• If the hose kinks or is damaged, a rupture may occur
which could cause serious injury. Replace the hose at the
first sign of wear, kink or damage.
• Only use the grease recommended in this manual
(Refer to the Technical information chart under Using the
grease gun).
• To reduce the risk of serious personal injury, do not use
the grease gun around or on moving parts, mechanisms
or running equipment.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught in
moving parts.

WARNING: Risk of injection or severe injury. Rupture
of components can inject grease into skin or eyes, causing
serious injury or infection. Do not treat as a simple cut.
Seek immediate medical attention.
6

WARNING: Output can be at high pressure. Do not
direct discharge at yourself or others.

WARNING: The grease gun may generate high
pressure—up to 10000 PSI (690 bar). Always wear
gloves during operation. Keep hands clear of the exposed
rubber portion of the hose.

WARNING: Grease and lubricants may be
flammable. Do not expose to flame or heat source.
Follow all warnings and instructions from grease and
lubricant manufacturer.

Additional Safety Information


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.

WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or dust
mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm. Some examples of
these chemicals are:
• lead from lead‑based paints,
• crystalline silica from bricks and cement and other masonry
products, and
• arsenic and chromium from chemically‑treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or
lay on the skin may promote absorption of harmful chemicals.
Direct particles away from face and body.
• Use the appropriate dust extractor vacuum to remove
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to the
operator and those in close proximity.
• Use clamps or other practical ways to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may lead
to loss of control and injury.

CAUTION: When not in use, place tool upright on rubber
feet on a stable surface where it will not cause a tripping or
falling hazard. Some tools with large battery packs will stand
upright on the battery pack but may be easily knocked over.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V .......................... volts
Hz ........................hertz
min ......................minutes
or DC ......direct current
....................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per
minute