Supplied Package; Proper Use; Technical Data - EINHELL RT-SM 430 U Mode D'emploi

Anleitung_RT_SM_430_U_SPK1:_
3. Supplied package (Fig. 1. 5)
Drag, crosscut and miter saw
Clamping device (8)
Roller support with limit stop (9)
2 x Holding bars for roller support (10)
Chip collection box (23)
4x Support feet (A)
2x Side parts (B)
2 x Intermediate struts (C)
4 x Corner reinforcements (D)
2 x Bottom cross struts (E)
2 x Top cross struts (F)
4 x Nuts (G)
4 x Washers (H)
32 x Nuts (I)
28 x Washers (K)
28 x Screws (L)
4 x Screws (N)
Allen key (O)
Allen key (P)
4 x Saw mount (J)
4 x Allen screw (M)

4. Proper use

The drag, circular crosscut and miter saw is designed
to crosscut wood and plastic suitable for the
machine's size. The saw is not designed for cutting
firewood.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The machine is to be operated only with suitable saw
blades. It is prohibited to use any type of cutting-off
wheel.
To use the machine properly you must also observe
the safety regulations, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the machine have
to be acquainted with this manual and must be
informed about its potential hazards.
It is also imperative to observe the accident
prevention regulations in force in your area.
08.04.2009 7:50 Uhr Seite 23
The same applies for the general rules of
occupational health and safety.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting
from such changes.
Even when the machine is used as prescribed it is
still impossible to eliminate certain residual risk
factors. The following hazards may arise in
connection with the machineʼs construction and
design:
Contact with the saw blade in the uncovered saw
zone.
Reaching into the running saw blade (cut
injuries).
Kick-back of workpieces and parts of workpieces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the saw
blade.
Damage to hearing if essential ear-muffs are not
worn.
Harmful emissions of wood dust when the
machine is used in closed rooms.

5. Technical data

Asynchronous motor
Output
Operating mode
Idle speed n
Carbide-tipped saw blade
Number of teeth
Tilting range
Mitre cuts
Sawing width at 90°
Sawing width at 45°
Sawing width at 2 x 45°
(double mitre cuts)
Weight
Laser class
Laser wave length
Laser output
Laser module power supply
Operating mode S6 40%: Continuous operation with
idling (cycle time 10 minutes). To ensure that the
motor does not become excessively hot it may only
be operated for 40% of the cycle at the specified
rating and must then be allowed to idle for 60% of
the cycle.
230 V~ 50 Hz
4800 min
0
ø 250 x ø 30 x 2.8 mm
-52° / 0°/ +60°
0° to 45° to the left
430 x 75 mm
300 x 75 mm
300 x 40 mm
2 x 1.5 V Micro (AAA)
GB
2200 W
S6 40%
-1
48
19,5 kg
2
650 nm
≤ 1 mW
23