R&G LP0376BK Instructions De Montage page 5

Page 1 of
- Use the larger diameter heat shrink supplied to cover the sub loom and the smaller
heat shrink to cover the number plate light and indicator wiring, using electrical
tape to seal/cover any gaps as required.
- Pass the wiring through the rubber bung, then cable tie the loom in place using the
cable tie slots as shown in the second diagram.
Offer up the tail tidy to the motorcycle and pass the connectors through the hole
-
in the undertray.
Then pass 2x of the supplied 25mm button head bolts (Item 6) with washers
-
through the rearward holes in the main bracket then through the motorcycles
undertray and hand tighten.
Please note: It is important you do not tighten the longer 25mm bolts into the
mounting holes closest to the front of the bike as this will damage the captive
Then pass the remaining 2x 20mm button head bolts (Item 4) through the forward
-
mounting holes and hand tighten.
- Connect the indicator and number plate light connectors to the original sub loom.
Test the indicators and number plate light function correctly before continuing
- Then fully tighten the bolts to the required torque spec.
IMPORTANT: FOR SAFETY, ENSURE THE LICENCE PLATE IS PLACED AS HIGH AS
POSSIBLE ON THE TAIL TIDY (IT MAY REQUIRE DRILLING). IF FITTING A
LICENCE PLATE OF 200MM OR LONGER (INCLUDING ANY SHROUD OR REFLECTOR
ATTACHMENT) TO THE BRACKET, BEFORE RIDING, FULLY COMPRESS THE
SUSPENSION TO ENSURE NO PART OF THE ASSEMBLY CAN CONTACT THE TYRE
WHILE THE
RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING
ACTION. FAILURE TO CHECK THIS COULD RESULT IN SERIOUS INJURY OR
DAMAGE TO THE MOTORCYCLE.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if
they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods
must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25%
of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges.
No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does
not refer to faulty goods.
Unit
Tel: +44 (0)
dome nuts on the inside of the tail unit.
VEHICLE IS IN
ISSUE 1 30/05/2024 TB
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
NOTICE DE MONTAGE LP0376BK
Racing Technique Ltd T/A R&G
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
420 89007 www.rg-racing.com Email: info@rg-racing.com
1
with the fitting.
MOTION OR UNDER
CONSUMER NOTICE
LP0376BK
LOAD. IT IS YOUR