R&G LP0375 Instructions De Montage
  1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. LP0375
  6. Instructions de montage

R&G LP0375 Instructions De Montage

Masquer les pouces

Table des Matières

Page 1 of 11
LP0375
FITTING INSTRUCTIONS FOR LP0375 LICENCE PLATE BRACKET
This kit contains the items pictured and labelled over page.
Some parts may be shown for clarity of instructions only.
Do not proceed until you are sure all parts are present.
Please read all instructions before proceeding.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike.
In the event of rubber washers being used to hold components onto bolts,
these rubber washers can be thrown away.
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM
WWW.RG-RACING.COM
R&G
Unit
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
Tel: +44 (0)
420 89007 Fax: +44 (0)
420 87301 www.rg-racing.com Email: info@rg-racing.com
1
1
Table des Matières
loading

Manuels Connexes pour R&G LP0375

Sommaire des Matières pour R&G LP0375

  • Page 1 Page 1 of 11 LP0375 FITTING INSTRUCTIONS FOR LP0375 LICENCE PLATE BRACKET This kit contains the items pictured and labelled over page. Some parts may be shown for clarity of instructions only. Do not proceed until you are sure all parts are present.

  • Page 2: Tools Required

    Page 2 of 11 LP0375 TOOLS REQUIRED GENERAL TORQUE SETTINGS Set of metric Hex keys M4 BOLT = 8Nm • T30 Torx head tool • M5 BOLT = Set of metric sockets and wrench. • M6 BOLT = 8mm & 10mm spanners.

  • Page 3: Assembly Diagram

    Page 3 of 11 LP0375 ASSEMBLY DIAGRAM FITTING PICTURES Picture 1 Picture 2 R&G Unit , Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0) 420 89007 Fax: +44 (0) 420 87301 www.rg-racing.com Email: info@rg-racing.com...

  • Page 4: Fitting Instructions

    Page 4 of 11 LP0375 Picture 3 Picture 4 Picture 5 Picture 6 FITTING INSTRUCTIONS Removing the OEM Tail Bracket 1. Remove the rear seat unit via the lock on the subframe & then rider seat. 2. Disconnect the rear indicator and number plate light connectors located under the pillion seat.
  • Page 5 Page 5 of 11 LP0375 6. Tighten down the indicator nuts. 7. Thread the licence plate illuminator (Item 3) cables through the licence plate bracket & the hole in Item 1 shown in Picture 4 then add the supplied washers and nuts to the threaded bars on the back of Item 3.
  • Page 6 No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods. NOTICE DE MONTAGE LP0375 SUPPORT DE PLAQUE E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE...

  • Page 7: Outils Requis

    Page 7 of 11 LP0375 WWW.RG-RACING.COM OUTILS REQUIS VALEURS DE SERRAGE Clés Allen M4 BOULON = 8Nm • LÉGEN Clé Torx T30 • M5 BOULON = Clé à cliquet + douilles • Clé à molette 8mm & 10mm • M6 BOULON = Tournevis cruciform •...
  • Page 8 Page 8 of 11 LP0375 PHOTOS DE MONTAGE Photo 1 Photo 2 Photo 3 Photo 4 R&G Unit , Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0) 420 89007 Fax: +44 (0) 420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 9 Page 9 of 11 LP0375 Photo 5 Photo 6 NOTICE DE MONTAGE Retrait du support arrière d’origine 4. Retirez l'unité de siège arrière via le verrou sur le sous-châssis, puis la selle du pilote. 5. Débranchez les connecteurs du clignotant arrière et de l'éclairage de plaque d'immatriculation situés sous la selle passager.
  • Page 10 Page 10 of 11 LP0375 13. Glissez les écrous et rondelles d’origine, suivis du cache câblage des clignotants (Article 9). Please note: Les cache-câbles devront peut-être être coupés à l'extrémité conique afin de faire passer les connecteurs à travers. 14. Serrez les écrous des clignotants.
  • Page 11 Page 11 of 11 LP0375 otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned.

Table des Matières