R&G LP0375 Instructions De Montage page 5

Page 5 of 11
6. Tighten down the indicator nuts.
7. Thread the licence plate illuminator (Item 3) cables through the licence plate bracket & the hole in
Item 1 shown in Picture 4 then add the supplied washers and nuts to the threaded bars on the
back of Item 3.
8. Thread the supplied cable ties (Item 11) through the slots on Item 1 shown in Picture 5.
1. With the 4X M6 bolts (Item 14) to hand, offer up the assembly to the motorcycles undertray.
2. Thread the indicator and licence plate illuminator cables through the wiring hole in the undertray &
gasket.
3. Thread the bolts through the tail tidy assembly, subframe, M6 washers and M6 nuts (Items 7 &
15) one by one until all four are tight enough to keep the assembly in position. Make sure the
rubber gasket is sandwiched between the bike & tail tidy bracket, and the protruding end
tucked up under the back of the brake light.
4. At this point attach the indicator and licence plate illuminator connectors to the OEM wiring
harness.
5. Check the operation of the indicators and licence plate lights – and that the LHS and RHS indicators
are in the correct orientation.
6. Find a suitable position to attach the cables/inline resistors to the underside of the tail bracket
(guide shown in Picture 6, green & red – indicator wires, blue – LA0002 wires).
7. Tighten down all four bolts evenly according to the general torque settings table.
IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT LOW DOWN ON THE
LICENCE PLATE MOUNT, THERE IS A POTENTIAL CHANCE THE LICENCE PLATE COULD HIT
THE BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE ROAD. IT IS YOUR
RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING ACTION. FAILURE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if
they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods
must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25%
of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges.
Unit
Tel: +44 (0) 420 89007 Fax: +44 (0)
1
Attaching the R&G Tail Tidy
TO CHECK THIS COULD RESULT IN SERIOUS INJURY.
ISSUE 2 - 10/12/2024 (MH)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
420 87301 www.rg-racing.com Email: info@rg-racing.com
1
R&G
LP0375