Intended Use; Know Your Product - Ryobi Rpd18X1 Traduction De La Notice Originale

EN ORIGINAL INSTRUCTIONS
Safety, performance, and dependability have been given top
priority in the design of your percussion drill.

INTENDED USE

The percussion drill is intended to be used only by adults
who have read and understood the instructions and
warnings in this manual and can be considered responsible
for their actions.
The product is intended for drilling into various materials,
including wood, metal, and plastics, using a drill bit having
a shank diameter of less than 13 mm. The product can
be used to drive and remove screws and bolts using an
appropriate bit.
The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the
product for operations diff erent from intended could result in
a hazardous situation.
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
PERCUSSION DRILL SAFETY WARNINGS
SAFETY INSTRUCTIONS FOR ALL OPERATIONS
■
Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
■
Use the auxiliary handle(s). Loss of control can cause
personal injury.
■
Brace the tool properly before use. This tool produces
a high output torque and without properly bracing the
tool during operation, loss of control may occur resulting
in personal injury.
■
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
SAFETY INSTRUCTIONS WHEN USING LONG DRILL BITS
■
Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
the workpiece, resulting in personal injury.
■
Always start drilling at low speed and with the bit
tip in contact with the workpiece. At higher speeds,
the bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
■
Apply pressure only in direct line with the bit and do
not apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal injury.
ADDITIONAL SAFETY WARNINGS
■
Clamp workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
■
Dust created by operating the product can cause
respiratory injury. Wear appropriate dust control mask
with filters suitable for protecting against particles from
the material being worked on.
■
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
■
Switch off the product immediately if the bit stalls. Do
not switch on the product again while the bit is stalled,
as doing so could trigger a sudden recoil with a high
reactive force. Determine why the bit stalled and rectify
this, paying heed to the safety instructions.
The possible causes may be:
●
it is tilted in the workpiece,
●
it has pierced the workpiece,
●
the product is overloaded.
■
Ambient temperature range for tool during operation is
between 0 °C and 40 °C.
■
Ambient temperature range for tool storage is between
0 °C and 40 °C.
■
The recommended ambient temperature range for the
charging system during charging is between 10 °C and 38 °C.
ADDITIONAL BATTERY SAFETY WARNINGS
■
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool,
battery pack, or charger in fluid or allow fluid to flow inside
them. Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.
■
Ambient temperature range for battery during use is
between 0 °C and 40 °C.
■
Ambient temperature range for battery storage is
between 0 °C and 20 °C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.

KNOW YOUR PRODUCT

See page 49.
1. Speed selector
2. Torque adjustment ring
3. Keyless chuck
4. Direction of rotation selector
5. Variable speed trigger
6. Handle, insulated gripping surface
7. LED light
8. Battery port
9. Auxiliary handle, insulated gripping surface
10. Belt clip screw
11. Belt clip
12. Operator's manual
13. Double bit
14. Drill bit
15. Battery pack
16. Charger
MAINTENANCE
■
The product should never be connected to a power supply
when assembling parts, making adjustments, cleaning,
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
3