Care And Maintenance; Mounting Accessories - Metabo Fp 18 Ltx Notice Originale

c) Press the switch (7) and exert some pressure
onto the screw-in cartridge from behind to promote
the flow of the grease.
d) It must be ensured that both the thread (33) of the
grease gun and the bearing of the screw-in adapter
(30) (see P. 3 fig. C) are completely free from air and
are filled with grease to that a negative pressure can
be generated.
e) During the first venting process, always exert
light pressure onto the end of the grease cartridge.
During the grease release, using the switch (7)
activate the venting (2) of the grease gun time and
again.
f) Vent until the grease exits without air bubbles.
Scan QR code to access the application video:
.

7. Care and Maintenance

Danger! Repair and maintenance work other
than described in this section should only be
carried out by qualified specialists .
- Check that all screw fittings are seated securely,
and tighten if necessary.
- Avoid contact with dangerous substances that
have collected on the tool. Wear suitable personal
protective equipment and take appropriate
measures to remove any dangerous substances
before maintenance.
f
8. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Chargers: ASC 55, ASC 145, etc.
Order no.: 627044000 ASC 55
Order no.: 627378000 ASC 145
etc.
Battery packs:
Order no.: 625367000 4.0 Ah (LiHD)
Order no.: 625368000 5.5 Ah (LiHD)
Order no.: 625369000 8.0 Ah (LiHD)
Order no.: 625026000 2.0 Ah (Li-Power)
Order no.: 625027000 4.0 Ah (Li-Power)
Order no.: 625028000 5.2 Ah (Li-Power)
etc.
For a complete range of accessories, see
www.metabo.com or the catalogue.
.

9. Mounting accessories

9.1 Mounting shoulder strap* (16) (p. 2 fig. A)
Can be attached to the metal eyelets (5) .
9.2 Mounting additional LED (22)
626982000 (p. 2 fig. B)
Place the silicone loop (28) around the hose and
hang it on the plastic hook (26) .
WARNING – To reduce the risk of injury,
read the operating instructions for the
additional LED (22) .
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with the additional LED
(22) . Failures to respect the instructions can cause
injuries.
9.3 Mounting magnet* (29)
626980000 (p. 2 fig. B)
Screw onto thread (21) for magnet.
WARNING – To reduce the risk of injury,
read the supplementary sheet of the magnet
(29).
WARNING – Read all safety warnings,
instructions, illustrations and
specifications that can be found on the magnet
(29). Failures to respect the instructions can cause
injuries or damage.
9.4 Mounting adapter* (30) (only for TV 00)
(p. 3 fig. C)
Permits the use of a screw-in cartridge. Screw the
adapter (30) onto the thread (33) and tighten it with
a suitable tool.
9.5 Mounting clamping coupling* (36)
626981000 (p. 3 fig. D)
Using a spanner*, remove the conical grease nipple
coupling (27) with a suitable tool, screw on the
clamping coupling* and tighten it with the tool.
*equipment-specific
10. Repairs
Repairs to electrical tools must only be carried
out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
ENGLISH en
13