Yaesu FT-817 Notice D'emploi page 60

E
MPLOI DU SYSTÉME DE MENU
Menu Item
01 144 ARS
02 430 ARS
03 9600 MIC
04 AM&FM DL
05 AM MIC
06 AM STEP
07 ANTENNA
08 APO TIME
09 ARTS BEEP
10 BACKLIGHT
11 BATT-CHG
12 BEEP FREQ
13 BEEP VOL
14 CAT RATE
15 COLOR
16 CONTRAST
17 CW DELAY
18 CW ID
19 CW PADDLE
20 CW PITCH
21 CW SPEED
22 CW WEIGHT
23 DCS CODE
24 DIG DISP
25 DIG MIC
26 DIG MODE
27 DIG SHIFT
28 EMERGENCY
29 FM MIC
30 FM STEP
31 ID
32 LOCK MODE
33 MAIN STEP
34 MEM GROUP
35 MEM TAG
58
Function
Activate/deactivate the Automatic Repeater Shift
when operating on the 144 MHz band
Activate/deactivate the Automatic Repeater Shift
when operating on the 430 MHz band
Adjust the audio input level from the TNC
during 9600 bps Packet operation
Enabling/disabling the
on the AM and FM modes
Adjust the microphone gain level for the AM mode
Select the tuning steps
for the knob on the AM mode
Select the antenna connector to be used
on each operating band (HF/50/144/430 MHz)
Select the Auto Power Off time
(time before power goes off)
Select the ARTS beep mode
Select the LCD lamp mode
Select the battery charging time
Select the beep frequency
Select the beep volume
Set the transceiver's circuitry for the CAT baud rate
Select the illumination color for the LCD illumination
Setting of the display contrast level
Set the receiver recovery time
during pseudo-VOX CW semi-break-in operation
Enables/disables the CW identifier
during ARTS operation
Select the keyer paddle's wiring configuration
Setting of the pitch of the CW sidetone, BFO offset,
and CW filter center frequencies
Set the sending speed for the built-in Electronic keyer
Set the Dot:Dash ratio for the built-in electronic keyer
Setting the DCS code
Define the displayed frequency offset
during DIG (USER-L or USER-U) mode operation
Adjust the audio input level from terminal equipment
(such as a TNC or PSK-31 sound card)
during DIG (Digital) mode operation
Select the mode and sideband (if applicable)
in the DIG (Digital) mode
Define the carrier frequency offset
during DIG (USER-L or USER-U) mode operation
Enable Tx/Rx operation on the Alaska Emergency Channel,
5167.5 kHz (USA Version only)
Adjust the microphone gain level for the FM mode
Select the tuning steps for the
on the FM mode
Store your callsign into the CW identifier
Select the operation of the front panel's
Setting of the 's tuning speed
Enable/disable the memory grouping feature
Store Alpha-Numeric "Tags" for the memory channels
knob
knob
key
Available Values
OFF/ON
OFF/ON
0 ~ 100
ENABLE/DISABLE
0 ~ 100
2.5/5/9/10/
12.5/25kHz
FRONT/REAR
OFF/1h ~ 6h
OFF/RANGE/ALL
OFF/ON/AUTO
6/8/10 h (hours)
440/880 Hz
0 ~ 100
4800/9600/38400 bps
COLOR1 (Blue)/
COLOR2 (Amber)
1 ~ 12
10 ~ 500 msec
OFF/ON
NORMAL/REVERSE
300 ~ 1000 Hz
4wpm ~ 60 wpm/
20cpm ~ 300 cpm
1:2.5 ~ 1:4.5
104 Std DCS codes
-3000 ~ +3000 Hz
0 ~ 100
RTTY/
PSK31-L/PSK31-U/
USER-L/USER-U
-3000 ~ +3000 Hz
OFF/ON
0 ~ 100
5/6.25/10/12.5/15/ 2
20/25/50 kHz
–
DIAL/FREQ/PANEL
FINE/COARSE
OFF/ON
–
FT-817 Notice d'emploi
Default
1
1
50
DISABLE
50
1
1
OFF
RANGE
AUTO
8 h
880 Hz
50
4800 bps
COLOR1
5
250 msec
OFF
NORMAL
700 Hz
12 wpm
(60 cpm)
1:3.0
023
0 Hz
50
RTTY
0 Hz
OFF
50
YAESU
DIAL
FINE
OFF
–