Control Throws; Prelight Checklist; Preflight Checklist; Daily Flight Checks - Hangar 9 ASH 31 6.4m Manuel D'utilisation

CONTROL THROWS

1. Turn on the transmitter and receiver of your model. Check the movement of the rudder using the transmitter.
When the stick is moved to the right, the rudder should also move right. Reverse the direction of the servo at the
transmitter if necessary.
2. Check the movement of the elevator with the radio system. Moving the elevator stick toward the bottom of the
transmitter will make the airplane elevator move up.
3. Check the movement of the ailerons with the radio system. Moving the aileron stick to the right will make the right
aileron move up and the left aileron move down.
4. Use a ruler to adjust the throw of the elevator, ailerons and rudder.
Surface Rate
Landing/Soaring
Aileron
Cruise/Launch
High
Elevator
Low
High
Rudder
Landing
Flaperon
Cruise/Launch
• In Landing or Soaring Mode, the ailerons will move independent from the laperons.
• In Landing or Soaring Mode, droop the entire trailing edge (laperons and ailerons) down 1/8–5/32 inches (3–4mm).
• In Cruise or Launch Mode, couple the ailerons and laperons for full roll control.
• In Cruise or Launch Mode, relex the entire trailing edge (laperons and ailerons) up 1/8–5/32 inches (3–4mm).
• Use a slider to control the laperon throw so the amount of travel can be varied.
• We recommend lowering the laperons 3/8 inches (10mm) during Rise-Off-Ground (ROG) takeoffs and
during aero-tow.
• Set the rudder throw to an amount that will not bind the servo.
• Set the maximum laperon throw to an amount that will not bind the servo.
These are general guidelines measured from our own light tests. You can experiment with higher rates to match your
preferred style of lying.
Travel Adjust and Sub-Trims are not listed and should be adjusted according to each individual model and preference.
Always install the control horns 90 degrees to the servo center line. Use sub-trim as a last resort to center the servos.
Always re-binding the radio system once all of the control throws are set to keep the servos from moving to their
endpoints until the transmitter and receiver connect.
www.modellmarkt24.ch; www.modellmarkt24.ch;
ASH 31 6.4M ARF
Direction Throw
Up 5/8 inches (16mm)
Down 15/32 inches (12mm)
Up 11/16–13/16 inches (18–20mm)
Down 17/32 inches (14mm)
Up 11/32 inches (9mm)
Down 9/32 inches (7mm)
Up 9/32 inches (7mm)
Down 3/16 inches (5mm)
Right 1 / / inches (35–45mm)
1 9
–1
8 32
Left
1 1 / 9 / inches (35–45mm)
–1
8 32
Down 1–1 / inches (25–30mm)
3
16
Up 11/16–13/16 inches (18–20mm)
Down 17/32 inches (14mm)

PREFLIGHT CHECKLIST

• Charge the transmitter, receiver and motor batteries. Follow the instructions provided with the charger. Follow all
manufacturer's instructions for your electronic components.
• Check the radio installation and make sure all control surfaces (aileron, elevator, rudder, laps and spoilers) move
correctly (i.e., the correct direction and with the recommended throws).
• Check all the hardware (control horns, servo horns, and clevises) to make sure they are secure and in good condition.
• Prior to each lying session (and especially with a new model), perform a range check of your radio system. See your
radio manual for the recommended range and instructions for your particular radio system.

DAILY FLIGHT CHECKS

• Check the battery voltage of the transmitter battery. Do not ly below the manufacturer's recommended voltage.
Doing so can cause your aircraft to crash.
• Check all hardware (linkages, screws, nuts, and bolts) prior to each day's light. Ensure that binding does not occur
and that all parts are properly secured.
• Ensure all surfaces are moving in the proper manner.
• Perform a ground range check before each day's lying session.
• All servo leads and switch harness plugs should be secured in the receiver.

LIMITED WARRANTY

What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the "Product") will be free from
defects in materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse,
abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modiication of or to
any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product
not purchased from an authorized Horizon dealer, (vi) Product not compliant with applicable technical regulations, or (vii) use
that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION,
AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS
OF THE PURCHASER'S INTENDED USE.
Purchaser's Remedy
Horizon's sole obligation and purchaser's sole and exclusive remedy shall be that Horizon will, at its option, either (i) service,
or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s)
involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is
required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER'S
SOLE AND EXCLUSIVE REMEDY.
www.modellmarkt24.de www.modellmarkt24.de
19 EN