Publicité
Les langues disponibles
Les langues disponibles
ADDITIONAL SAFETY WARNINGS
■
Always clamp the workpiece safely and securely.
■
Ensure that the product is always stable and secure
(e.g., fixed to a bench).
■
Always wear ear protectors. Exposure to noise can
cause hearing loss.
■
Always wear safety goggles when using the product.
It is recommended to wear gloves for handling blades
and rough material, plus sturdy non slip shoes to
protect the feet from workpieces which may fall from
the cutting area.
■
Disconnect the product from the mains supply or remove
battery pack before carrying out any maintenance or
cleaning the product.
■
Only install the battery pack when the product is
switched off.
■
Never reach into the area near the blade unless the
blade has completely stopped.
■
Before use, thoroughly check the product and battery
pack for any damage or material fatigue. Repairs to
the whole product should only be carried out by an
authorised service centre.
■
Always use the guards on the product. Do not use
the product if the guards are not in place and working
correctly.
■
The lower blade guard should only open when the
blade is lowered to the workpiece and must always be
able to move freely and close automatically.
■
Always fix and use extension bars for workpiece
support during operation.
■
Never alter of modify the product or its function. Your
safety may be compromised.
■
Do not use saw blades which are cracked, damaged
or deformed.
■
Do not use saw blades made of high-speed steel.
■
Only use blades that are sharp. Replace dull blades.
■
Always use blades with correct size and shape of
arbour holes. Blades that do not match the mounting
hardware of the saw will run eccentrically, causing loss
of control.
■
Use only woodworking blades specified in this manual,
which comply with EN 847-1.
■
Do not use any flanges, washers and nuts to secure the
saw blade other than those supplied or indicated in the
instruction manual.
■
It is necessary to select a saw blade which is suitable
for the material being cut. Never use the product to cut
materials other than those specified in the intended use
section in this manual.
■
It is important to avoid overheating the blade and
melting the plastic when cutting.
■
It is essential to adhere to the maximum speed specified
on the saw blade, only use saw blade that are marked
with a speed equal or higher than the speed marked
on the tool.
■
Replace the table insert when worn or damaged.
■
Before work, make a dummy cut without the motor
turned on so the position of the blade, operation of
the guards with respect to other machine parts, and
workpiece may be checked.
4
Original Instructions
■
When performing mitre, bevel or compound mitre cuts,
adjust the sliding fence or sub-fence to ensure the
correct clearance from the blade.
■
Avoid uncontrolled release of the saw unit from the fully
down position.
■
The handle lock must always be engaged when
transporting the product.
■
Keep the floor area free of loose materials, such as
chips and cut-offs.
■
Refrain from removing any cut-offs or other parts of the
workpiece from the cutting area whilst the product is
running and the saw head is not in the rest position.
■
Long workpieces must be adequately supported. The
working area of the saw includes the whole extent of the
workpiece. The operator should secure this area from
accidental contact from other persons or objects which
may move the workpiece during operation.
■
The dust produced when using the product may be
harmful to health. Use a dust suction system and wear
a suitable dust protection mask. Remove deposited
dust thoroughly with a vacuum cleaner.
■
Do not replace the laser with a different type. Any
repairs must only be carried out by the manufacturer or
authorised service agent.
■
Ambient temperature range for tool during operation is
between 0 ˚C and 40˚ C.
■
Ambient temperature range for tool storage is between
0 ˚C and 40˚ C.
■
The recommended ambient temperature range for the
charging system during charging is between 10 ˚C and
38˚ C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
ADDITIONAL BATTERY SAFETY WARNINGS
To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to
fl ow inside them. Corrosive or conductive fl uids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■
Ambient temperature range for battery during use is
between 0 ˚C and 40˚ C.
■
Ambient temperature range for battery storage is
between 0 ˚C and 20˚ C.
WARNING
Publicité
