Worx WG772E Mode D'emploi page 15

mower too many times during operation will reduce
the cutting area.
The table below gives the relationship between
cutting conditions and cutting area.
Cutting Conditions
Grass Cutting
conditions height
Very thin, dry Cut 6cm
grass to 4cm
Cut 8cm
Thin, dry grass
to 4cm
* Used 2 fully charged battery packs at the same
time.
TIPS:
1) It is recommended to mow your lawn more
frequently, walk at normal pace, and not to start/
stop the mower too often during operation.
2) For best performance, please ensure use two
fully charged battery packs at the same time and
always cut off 1/3 or less of the grass height.
3) Walk slowly when cutting long grass, so as
to have more effective cutting and properly
discharge the clippings.
4) Avoid cutting wet grass, otherwise it will stick
to the underside of the deck and the clippings
cannot be collected or discharged properly.
5) A higher cutting height shall be applied to new
or thick grass and it will extend the battery
duration.
MULCHING MOWING TIPS
While mulching, your new mower is designed to cut
the grass clippings into small pieces and distribute
them back into the lawn. Under normal conditions,
the mulched grass will biodegrade quickly and
deliver nutrients to the lawn. Please review the
following recommendations for optimum mulching
performance.
1) Avoid mowing when the grass is wet from rain
or dew. Wet grass may form clumps which
interfere with the mulching action and reduce
the runtime. The best time to mow the grass is
in the late afternoon when the grass is dry and
the newly cut area will not be exposed to direct
sunlight.
2) For the best mulching performance, set the
cutting height to remove about one third of
the grass blade length, ideally no more than
40mm at one time. If the lawn is overgrown,
it may be necessary to increase the cutting
height to reduce the pushing effort and prevent
overloading the motor. For extremely heavy
mulching, it is advisable to first cut at a high
cut height setting, and then re-cut to the final
cut height. Otherwise, make narrower cuts and
mow slowly.
3) For the best performance, keep the mower
housing free of built-up grass. From time to
Cordless Lawn Mower
All manuals and user guides at all-guides.com
Cutting Area
(maximum)
WG772E WG772E.9
600m *
2
350m *
2
time turn off mower and wait for the blades
to come to a complete stop. Then unplug
the safety key and turn mower on its side.
Using an object such as a stick, wipe out any
accumulation of grass around the blade area.
Be careful of the sharp edges of the blade.
Ensure to clean the blade area often when
cutting wet or new grass and every time after
the machine is used.
4) Certain types of grass or grass conditions may
require that an area be mulched a second time
to fully disperse the grass throughout the lawn.
If cutting a second time, it is advisable to cut
perpendicular (across) the first cut pattern. DO
NOT CHANGE CUT PATTERN IN ANY WAY THAT
WOULD CAUSE MOWING DOWN A HILL.
5) Change your cutting pattern from week to week.
This will help prevent matting and graining of
the lawn.
MAINTENANCE
WARNING: Stop the mower and remove
the safety key before removing the
grass bag.
NOTE: To ensure long and reliable service, perform
the following maintenance procedures regularly.
Check for obvious defects such as a loose, dislodged
or a damaged blade, loose fittings, and worn or
damaged components. Check that the covers and
guards are all undamaged and are correctly attached
to mower. Carry out any necessary maintenance
or repairs before operating mower. If the mower
should happen to fail despite regular maintenance,
please call our customer helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER
PERFORMANCE. A DULL BLADE DOES NOT CUT
GRASS CLEANLY OR MULCH PROPERLY.
WEAR PROPER EYE PROTECTION WHILE
REMOVING, SHARPENING, AND INSTALLING
BLADE. ENSURE THAT SAFETY KEY IS REMOVED.
Sharpening the blade twice during a mowing
season is usually sufficient under normal
circumstances. Sand causes the blade to dull
quickly. If your lawn has sandy soil, more frequent
sharpening may be required.
REPLACE BENT OR DAMAGED BLADE
IMMEDIATELY.
WHEN SHARPENING THE BLADE:
(See Fig. L)
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade,
removing equal amounts of material from both
ends.
NOTE:
1. Be sure the mower is turned off and remove the
key.
2. Place the mower in stand up storage mode.
15
EN