Publicité
Les langues disponibles
Les langues disponibles
Conductor size (mm
2
)
Cable rating (Amperes)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
7.5
Voltage
Amperes
Cable rating (Amperes)
115
0 - 2.0
6
2.1 - 3.4
6
3.5 - 5.0
6
5.1 - 7.0
10
7.1 - 12.0
15
12.1 - 20.0
20
220/240
0 - 2.0
6
2.1 - 3.4
6
3.5 - 5.0
6
5.1 - 7.0
10
7.1 - 12.0
15
12.1 - 20.0
20
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Removing and fitting a cutting disc (fig. B)
Cutting discs with a bore of 25,4 mm (standard)
• Press and hold down the spindle lock (5).
• Rotate the cutting disc until it locks.
• Using the spanner supplied, release the disc
retaining bolt (10) and remove it completely with
the outer retaining flange (11).
• Release the spindle lock (5).
• Replace the cutting disc and secure it with the
outer retaining flange (11) and the disc retaining
bolt (10).
Clamping the workpiece in position (fig. A)
Your D
WALT chopsaw is equipped with a quick-
E
adjusting material clamp (6).
Clamping materials with a maximum width of 110
mm (fig. C)
• Pull lever (13) in the direction of arrow (14).
• Push the clamp shaft (15) forward until jaw (16) is
almost touching the workpiece to be cut.
15
All manuals and user guides at all-guides.com
Cable length (m)
15
25
30
45
60
6
6
6
6
10
6
6
6
15
15
6
10
15
20
20
10
15
20
20
25
15
20
25
25
-
20
25
-
-
-
6
6
6
6
6
6
6
6
6
6
6
6
6
10
15
10
10
10
15
15
15
15
15
20
20
20
20
20
25
-
• Press lever (13) in the direction of arrow (17) until
it engages with the clamp shaft (15).
• Rotate the handle (18) clockwise and clamp the
workpiece securely.
• To release the workpiece, rotate the handle (18)
counterclockwise.
Clamping materials with a maximum width of 230
mm (fig. D)
• Loosen the two bolts (19) using the spanner
supplied with the tool.
• Slide fence (20) as far as necessary.
• Tighten the two bolts (19).
When cutting square or rectangular
section material, position the material
slightly off-centre towards the rear of the
tool.
Adjusting the angle of cut (fig. D)
This D
WALT chopsaw can be used for left and right
E
mitre cuts up to 45°.
• Loosen the two bolts (19) using the spanner
supplied with the tool.
• Adjust the fence (20) to the required angle. When
turning the fence in the direction of arrow (21),
line up the scale with the right-hand side of the
slot (23). When turning the fence in the direction
of arrow (22), line up the scale with the left-hand
side of the slot (23).
• Tighten the two bolts (19) and clamp the
workpiece securely.
Instructions for use
• Always observe the safety instructions
and applicable regulations.
• Do not apply excessive pressure to the
tool.
• Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Prior to operation:
• Install the appropriate cutting disc. Do not use
excessively worn discs. The maximum rotation
speed of the tool must not exceed that of the
cutting disc.
E N G L I S H
en - 4
Publicité
