Publicité
Les langues disponibles
Les langues disponibles
b)
Avoid body contact with earthed or ground-
ed surfaces, such as pipes, radiators, rang-
es and refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c)
Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk
of electric shock.
Do not abuse the cord. Never use the cord
d)
for carrying, pulling or unplugging the pow-
er tool. Keep cord away from heat, oil, sharp
edges or moving parts.
Damaged or entangled cords increase the risk
of electric shock.
When operating a power tool outdoors, use
e)
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f)
If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a)
Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b)
Use personal protective equipment. Always
wear eye protection.
Protective equipment such as a dust mask, non-
skid safety shoes, hard hat or hearing protection
used for appropriate conditions will reduce per-
sonal injuries.
c)
Prevent unintentional starting. Ensure the
switch is in the off-position before connect-
ing to power source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d)
Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
Do not overreach. Keep proper footing and
e)
balance at all times.
This enables better control of the power tool in
unexpected situations.
f)
Dress properly. Do not wear loose clothing
or jewellery. Keep your hair and clothing
away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
If devices are provided for the connection of
g)
dust extraction and collection facilities, en-
sure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
h)
Do not let familiarity gained from frequent
use of tools allow you to become compla-
cent and ignore tool safety principles.
A careless action can cause severe injury within
a fraction of a second.
4) Power tool use and care
a)
Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b)
Do not use the power tool if the switch does
not turn it on and off.
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
Disconnect the plug from the power source
c)
and/or remove the battery pack, if detacha-
ble, from the power tool before making any
adjustments, changing accessories, or stor-
ing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
Store idle power tools out of the reach of
d)
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of un-
trained users.
e)
Maintain power tools and accessories.
Check for misalignment or binding of mov-
ing parts, breakage of parts and any other
condition that may affect the power tool's
operation. If damaged, have the power tool
repaired before use.
Many accidents are caused by poorly main-
tained power tools.
Keep cutting tools sharp and clean.
f)
Properly maintained cutting tools with sharp cut-
ting edges are less likely to bind and are easier
to control.
g)
Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous
situation.
h)
Keep handles and grasping surfaces dry,
clean and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
GB | 25
Publicité
