Worx WG776E Mode D'emploi page 13

and-down. Exercise extreme caution when
changing direction on slopes. do not mow
excessively steep slopes. Always maintain
good footing.
2. Release switch lever to turn mower "OFF"
when crossing any graveled area (stones
can be thrown by the blade).
3. Set mower at highest cutting height when
mowing in rough ground or in tall weeds.
Removing too much grass at one time can
cause circuit breaker to trip, which stops
mower.
4. if a grass bag is used during the fast
growing season, the grass may tend to clog
up at the discharge opening. Release switch
lever to turn mower "OFF" and remove
the safety key. Remove the grass bag and
shake the grass down to the back end of
the bag. Also clean out any grass or debris
which may be packed around the discharge
opening. Replace the grass collection bag.
5. if mower should start to vibrate
abnormally, release switch lever to turn
mower "OFF" and remove safety key.
Check immediately for cause. Vibration is a
warning of trouble. do not operate mower
until a service check has been made.
6. ALwAyS RELEASE SwITCh LEVER TO
TURN MOwER "OFF" AND REMOVE
SAFETy KEy whEN LEAVING IT
UNATTENDED EVEN FOR A ShORT
PERIOD OF TIME.
MAInTEnAnCE
wARNING: Stop the mower and
remove the safety key before
removing the grass bag.
NOTE: To ensure long and reliable service,
perform the following maintenance
procedures regularly. Check for obvious
defects such as a loose, dislodged or a
damaged blade, loose fittings, and worn
or damaged components. Check that the
covers and guards are all undamaged and
are correctly attached to mower. Carry out
any necessary maintenance or repairs before
operating mower. if the mower should
happen to fail despite regular maintenance,
please call our customer helpline for advice.
Cordless lawn mower
All manuals and user guides at all-guides.com
BLADE ShARPENING
KEEp BLAdE ShARp FOR BEST MOWER
pERFORMANCE.
WEAR pROpER EYE pROTECTiON WhiLE
REMOViNG, ShARpENiNG, ANd iNSTALLiNG
BLAdE. ENSURE ThAT SAFETY KEY iS REMOVEd.
Sharpening the blade twice during a mowing
season is usually sufficient under normal
circumstances. Sand causes the blade to dull
quickly. if your lawn has sandy soil, more
frequent sharpening may be required.
REpLACE BENT OR dAMAGEd BLAdE
iMMEdiATELY.
whEN ShARPENING ThE BLADE:
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of
TO ShARPEN BLADE IN A VISE
(See Fig. K)
1. Be sure the switch lever is released, the
2. Remove blade from mower. See
3. Secure blade K-1 in a vise K-2.
4. Wear safety glasses and be careful not to
5. Carefully file the cutting edges of the blade
6. Check balance of blade. See instructions
7. Replace blade on mower and tighten
BLADE BALANCING (See Fig. L)
Check balance of blade by placing center hole
in blade L-1 over a nail or screwdriver shank L
-2, clamped horizontally in a vise L-3. if either
end of the blade rotates downward, file that
end. Blade is properly balanced when neither
end drops.
BLADE MAINTENANCE (See Fig. M1,M2)
Renew your metal blade after 50 hours
blade, removing equal amounts of material
from both ends.
blade has stopped and the safety key
removed before removing the blade.
instructions for removing and attaching
blade.
cut yourself.
with a fine tooth file K-3 or sharpening
stone.
for blade balancing.
securely. Refer to instructions below.
13
En