Ryobi EAG950RBD Traduction Des Instructions Originales page 3

WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
ANGLE GRINDER SAFETY WARNINGS
SAFETY WARNINGS COMMON FOR GRINDING OR
ABRASIVE CUTTING-OFF OPERATIONS
a) This power tool is intended to function as a
grinder and cut-off tool. Read all safety warnings,
instructions, illustrations
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury.
b) Operations such as sanding, wire brushing or
polishing are not recommended to be performed
with this power tool. Operations for which the power
tool was not designed may create a hazard and cause
personal injury.
c) Do not use accessories which are not specifically
designed and recommended
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories cannot
be adequately guarded or controlled.
f) Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted
by flanges, the arbour hole of the accessory must
fit the locating diameter of the flange. Accessories
that do not match the mounting hardware of the power
tool will run out of balance, vibrate excessively and may
cause loss of control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test
time.
h) Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
i)
j)
and specifications
k) Position the cord clear of the spinning accessory.
l)
by the tool
m) Do not run the power tool while carrying it at your
n) Regularly clean the power tool's air vents. The
o) Do not operate the power tool near flammable
p) Do not use accessories that require liquid coolants.
FURTHER
OPERATIONS
Kickback and related warnings
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory, which in turn causes the uncontrolled power
tool to be forced in the direction opposite of the accessory's
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending
on the direction of the wheel's movement at the point of
pinching. Abrasive wheels may also break under these
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping flying debris generated by various operations.
The dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged
exposure to high intensity noise may cause hearing
loss.
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
workpiece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
Never lay the power tool down until the accessory
has come to a complete stop. The spinning accessory
may grab the surface and pull the power tool out of your
control.
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
materials. Sparks could ignite these materials.
Using water or other liquid coolants may result in
electrocution or shock.
SAFETY INSTRUCTIONS
EN
English
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
Fragments of
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
EL
TR
FOR ALL
1