Table des Matières
Publicité
Note: For safety reasons, the on/off switch (5) cannot be
locked; it must remain pressed during the entire operation.
Practical advice
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Parking rest (see figure D)
The parking rest (25) makes it possible to put down the
power tool directly after working, without any danger of
damaging the workpiece or planer blade. During the work
process, the parking rest (25) is highly pivoted and the rear
section of the planer base plate (7) is released.
Note: The parking rest (25) must not be removed.
Planing Procedure (see figure D)
Set the required cutting depth and position the power tool
with the front section of the planer base plate (7) on the
workpiece.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Switch on the power tool and guide it over the surface of the
workpiece, applying uniform feed.
To achieve high-quality surfaces, apply only a low feed rate
and exert pressure on the middle of the planer base plate.
For the processing of hard materials, such as hardwood, and
also when utilising the maximum planing width, set only a
low cutting depth and reduce the planer feed as appropriate.
Excessive feed reduces the quality of the surface finish and
can lead to the chip ejector quickly becoming blocked.
Only sharp planer blades achieve good cutting performance
and make the power tool last longer.
The integrated parking rest (25) also enables a continuation
of the planing procedure following interruption at any point
on the workpiece:
– Place the power tool – with parking rest folded down –
onto the area of the workpiece that you will continue to
work on.
– Switch the power tool on.
– Shift the contact pressure onto the front of the planer
base plate and slowly slide the power tool forward (➊). In
doing so, the parking rest will swivel upwards and out of
the way (➋), meaning that the rear section of the planer
base plate is in contact with the workpiece again.
– Guide the power tool over the surface of the workpiece,
applying uniform feed (➌).
Chamfering edges (see figure E)
The V-groove (8) in the front of the planer base plate enables
quick and easy chamfering of workpiece edges. Position the
planer with the V-groove onto the edge of the workpiece and
guide it along.
Bosch Power Tools
Groove used
None
Medium
Planing with the Parallel/Angle Guide (see figures F–H)
Attach the parallel guide (17) or the angle guide (21) to the
power tool with the fastening screw (20). Depending on the
application, attach the rebate depth guide (24) to the power
tool with the fastening screw (23).
Loosen the locking nut (19) and set the desired rebate width
on the scale (18). Retighten the locking nut (19).
Set the desired rebate depth accordingly using the rebate
depth guide (24).
Carry out the planing procedure several times until the de-
sired rebate depth has been achieved. Guide the planer with
sideways contact pressure.
Chamfering with angle guide
Maintenance and Service
Maintenance and cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Keep the parking rest (25) clear and clean it regularly.
When the carbon brushes are worn out, the power tool
switches itself off. The power tool must be sent to the after-
sales service for maintenance; see the "After-sales service
and advice on using products" section for addresses.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
English | 15
Dimension a
(mm)
0–4
4–9
Use the angle setting (22) to
set the necessary helix angle
when chamfering grooves
and surfaces.
1 609 92A 4LF | (05.11.2020)
Publicité
Table des Matières
