Practical Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch Professional GSR 18V-28 Notice Originale

18 | English
GSB 18V-28
Set the operating mode presetting ring (4) to
the "drilling" symbol.
Screwdriving
GSR 18V-28
Set the torque presetting ring (3) to the re-
quired torque.
GSB 18V-28
Set the operating mode presetting ring (4) to
the "screwdriving" symbol.
Set the torque presetting ring (3) to the re-
quired torque.
Impact drilling
GSB 18V-28
Set the operating mode presetting ring (4) to
the "impact drilling" symbol.
Switching on/off
To start the power tool, press and hold the on/off switch
(11).
The LED (8) lights up when the on/off switch (11) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (11).
Adjusting the Speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (11) to varying extents.
A light pressure on the on/off switch (11) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Pre-selecting the torque
The torque presetting ring (3) can be used to pre-select the
required torque in 20 stages. Once the set torque has been
reached, the application tool will be stopped.
Mechanical gear selection
Only operate the gear selector (5) when the power
u
tool is not in use.
Always push the gear selector switch as far as it will
u
go. Otherwise, the power tool may become damaged.
First gear:
Low speed range; for working with a large drilling diameter
or for screwdriving.
Second gear:
High speed range; for working with a small drilling diameter.
Temperature-dependent overload protection
When used as intended, the power tool cannot be over-
loaded. In the event of overloading or the temperature
rising/falling outside the permitted operating temperature
range, the speed will be reduced. The power tool will not run
at full speed again until the permitted operating temperature
has been reached.
Activation of the temperature-controlled overload protector
is indicated by the LED (9) on the power tool lighting up red.
1 609 92A 839 | (22.09.2022)
To return to within the permitted operating temperature
range, switch the gear selector (5) to first gear, run the
power tool at no load or wait until the LED (9) goes out.
When the LED (9) has gone out, the tool has returned to
within the permitted operating temperature range.

Practical advice

An auxiliary tool can be used to remove the screwdriver bit
or universal bit holder.
Only apply the power tool to the screw when the tool
u
is switched off. Rotating application tools can slip off.
Belt clip (see figure D)
You can use the belt clip (14) to hang the power tool on a
belt, for example. You then have both hands free and the
power tool is always at hand.

Maintenance and Service

Maintenance and Cleaning

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
Bosch Power Tools