Switching On/Off; Practical Advice; Maintenance And Service; Maintenance And Cleaning - Bosch Uneo Notice Originale

– To change the operating mode, turn the impact/mode se-
lector switch (4) to the required position.
Position for hammer drilling into concrete,
brick or stone
Position for drilling without impact in wood
and metal
Position for screwdriving
Setting the rotational direction (see figure G)
Only operate the rotational direction switch (8) when
u
the power tool is not in use.
The rotational direction switch (8) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (9) is being pressed.
– Right rotation: To drill and to drive in screws, press the
rotational direction switch (8) through to the left stop.
The rotational direction indicator for right rotation
(5) lights up when the on/off switch (9) is pressed
and the motor is running.
– Left rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (8) through to the
right stop.
The rotational direction indicator for left rotation
(7) lights up when the on/off switch (9) is pressed
and the motor is running.

Switching On/Off

– To start the power tool, press and hold the on/off switch
(9).
The lamp (11) lights up when the on/off switch (9) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
For low temperatures, the power tool reaches the full ham-
mer/impact capacity only after a certain time.
– To switch off the power tool, release the on/off switch
(9).
Adjusting the Speed/Impact Rate
– Adjust the speed/impact rate of the power tool when it is
on by pressing in the on/off switch (9) to varying extents.
Applying light pressure to the on/off switch (9) results in a
low rotational speed/impact rate. Applying increasing pres-
sure to the switch increases the speed/impact rate.

Practical Advice

Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
Bosch Power Tools
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.

Maintenance and Service

Maintenance and Cleaning

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
packaging. Please also observe the possibility of more de-
tailed national regulations.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
English | 17
1 609 92A 86E | (13.07.2022)