General Power Tool Safety Rules - Delta ShopMaster S26-260L Mode D'emploi

Additional information regarding the safe and proper operation of this tool is available from the following sources:
• Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851or online at www.powertoolinstitute.com
• National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201
• American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org - ANSI 01.1 Safety Requirements
for Woodworking Machines
• U.S. Department of Labor regulations www.osha.gov

GENERAL POWER TOOL SAFETY RULES

• READ INSTRUCTION MANUAL AND KNOW
YOUR TOOL. Read and familiarize yourself with
entire instruction manual. Learning the tool's proper
applications, limitations, and specific potential
hazards will greatly minimize the possibility of
accidents and injury. Make sure all users are familiar
with its warnings and instructions before using tool.
• KEEP GUARDS IN PLACE and in working order.
• REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that all adjusting keys
and wrenches are removed before starting tool.
• KEEP WORK AREA CLEAN AND WELL LIT. Cluttered
or poorly lit work areas, surfaces and benches can
lead to accidents.
• DO NOT USE OR STORE TOOL IN DANGEROUS
ENVIRONMENTS. Exposure to rain and damp or
wet locations can result in shock or electrocution,
or damage the tool. Do not operate electric tools
near flammable liquids or in gaseous or explosive
atmospheres. Motors and switches in these tools
may spark and ignite fumes.
• KEEP CHILDREN AND BYSTANDERS AWAY from
work area.
• LOCK TOOLS AND WORK AREA. Use padlocks, and
master switches, or remove and store starter keys to
prevent operation by children and other unauthorized
users.
• DO NOT FORCE TOOL OR WORKPIECE. Operate
tool at intended speed and feed rate for better and
safer operation.
• USE PROPER TOOL. Do not force tool to do a task
for which it was not designed.
• DO NOT ABUSE POWER CORDS. NEVER pull on
cord to disconnect from receptacle, crush cord, or
expose it to heat, oil or sharp objects.
• USE PROPER EXTENSION CORD. If you use an
extension cord, make sure it is in good condition and
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating.
See Extension Cord Chart for correct size depending
on cord length and data plate ampere rating. If in
doubt, use the next smaller gauge number. The
smaller the gauge number, the heavier the cord.
When working outside, make sure extension cord
is rated for outdoor use. Consult power connection
section of this manual for Extension Cord Chart and
power connection safety.
• SECURE WORKPIECE. Use clamps or a vise to hold
the work piece when practical. It is safer than using
your hands and frees both hands to operate tool.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
• DO NOT OVERREACH. Keep proper footing and
balance to maintain control.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
• DISCONNECT TOOLS before servicing; when
changing accessories, such as blades, or adjusting the
laser calibration..
• TO REDUCE RISK OF ACCIDENTAL STARTING, make
sure power switches are in "OFF" position before
plugging tool in.
• DO NOT touch the plug's metal prongs when
unplugging or plugging in the cord.
• USE RECOMMENDED ACCESSORIES. Consult
manual for recommended accessories. Use of
inappropriate accessories may cause personal injury or
property damage.
• NEVER STAND ON TOOL. Serious injury could occur if
the tool tips or if you unintentionally contact the cutting
surface.
• CHECK TOOLS FOR DAMAGE. Before using, and
after tool or accessory has been dropped or damaged,
check guards and affected parts for alignment of
moving parts, binding of moving parts, breakage
of parts, and any other condition that may affect its
operation to make sure tool will operate properly and
all parts will perform their intended function. Do not
use a damaged product. A guard or any other part that
is damaged should be properly repaired or replaced
using factory approved service parts.
• USE PROPER FEED DIRECTION. Feed work piece
against the direction of rotation of the tool's blade,
cutter, or abrasive surface. Feeding in the other
direction may cause the work piece to be thrown at
high speed.
• NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
POWER OFF. Do not leave tool until it comes to a
complete stop. In the event of a power failure, move
switch to "OFF" position.
• STAY ALERT; WATCH WHAT YOU ARE DOING, AND
USE COMMON SENSE. Do not use power tools
when tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating
power tools may result in injury.
• SERVICE PARTS. Use only identical replacement parts
when servicing your tool.
• WEAR PROPER APPAREL. Do not wear loose clothing,
gloves, neckties, rings, bracelets, or other jewelry
which may get caught in moving parts. Nonslip
protective footwear is recommended. Wear protective
hair covering to contain long hair.
3