Ca-Mi AS-36BR Mode D'emploi page 21

GB
The surgical aspirator AS-36 BR is intended for use in the electromagnetic environment specified below.
The customers or the user of the surgical aspirator AS-36 BR should assure that it's used in such an environment.
Immunity Test Level indicated by the
Electrostatic
discharge (ESD)
EN 61000-4-2
Electrical fast
transient / burst
EN 61000-4-4
Surge ± 1kV differential mode
EN 61000-4-5
Loss of voltage, brief
voltage interruptions
and variations
EN 61000-4-11
Magnetic field
EN 61000-4-8
Nota U is the value of the power supply voltage
T
The surgical aspirator AS-36 BR is intended for use in the electromagnetic environment specified below.
The customers or the user of the surgical aspirator AS-36 BR should assure that it's used in such an environment.
Immunity Test
Conducted Immunity
EN 61000-4-6
Radiated Immunity
EN 61000-4-3
Note 1: At 80 MHz and 800 MHz the interval with the highest frequency is applied
Note 2: These guide lines may not be applicable in all situations. The electro-magnetic propagation is influenced by the
absorption and by reflection from buildings, objects and people.
a) The field intensity for fixed transmitters such as the base stations for radiotelephones (mobile and cordless) and terrestrial
mobile radio, amateur radio devices, radio AM and FM transmitters and TV transmitters can not be theoretically and
accurately foreseen. To establish an electro-magnetic environment generated by fixed RF transmitters, an electro-magnetic
study of the site should be considered. If the field intensity measured in the place where the device will be used surpasses the
above mentioned applicable level of conformity, the normal functioning of the device should be monitored. If abnormal
performance arises, additional measures such as changing the device's direction or positioning may be necessary.
b) The field intensity on an interval frequency of 150 kHz to 80 MHz should be less than 3 V/m.
Guidance and manufacturer's declaration – Immunity Emissions
EN 60601-1-2
± 6kV on contact
± 8kV in air
± 2kV power supply
lines
± 1kV for input /
output lines
5%U (>95% dip U )
T T
for 0.5 cycle
40%U (>60% dip U )
T T
for 5 cycle
70%U (>30% dip U )
T T
for 25 cycle
<5%U (>95% dip U )
T T
for 5 sec
3A/m
Guidance and manufacturer's declaration – Immunity Emissions
Level indicated by
the EN 60601-1-2
3Vrms 150kHz to
80Mhz (for non life-
supporting devices)
3V/m 80MHz to
2.5GHz (for non life-
supporting devices)
Compliance Level Electromagnetic environment - guidance
The device doesn't Floors should be wood, conceret or ceramic tile.
change its state If floors are covered with synthetic material, the
relative humidity should be at least 30%.
The device doesn't Mains power quality should be that of a typical
change its state commercial environment or hospital.
The device doesn't Mains power quality should be that of a typical
change its state commercial environment or hospital.
- Mains power quality should be that of a typical
commercial environment or hospital If the user of
the surgical aspirator AS-36 BR request that the
appliance operates continuously, the use of a
continuity unit is recommended.
The device doesn't The power frequency magnetic field should be
change its state measured in the intended installation location to
assure that it's sufficiently low.
Compliance Electromagnetic environment - guidance
Level
V = 3 V rms The portable and mobile RF communication devices,
1
including cables, must not be used closer to the AS-36 BR
device, than the separation distance calculated by the
equation applicable to the transmitter frequency.
E = 3 V / m
1
Recommended separation distance
d = [3.5 / V
d = [12 / E
d = [23 / E
Where P is the maximum nominal output voltage of the
transmitter in Watt (W) depending on the manufacturer of
the transmitter and the recommended separation distance
in metres (m). The intensity of the field from the fixed RF
transmitters, as determined by an electro-magnetic study
of the site
each frequency interval
interference in proximity to devices identified by the
following symbol:
21
]
P
1
] P from 80 MHz to 800MHz
1
] P from 800 MHz to 2.5 GHz
1
, could be lower than the level of conformity of
a)
. It is possible to check for
b)