Cleaning Of Accessories - Ca-Mi AS-36BR Mode D'emploi

Table des Matières

Les langues disponibles

EUROPEAN POWER SUPPLY CORD FOR AC/DC ADAPTER

On request, are available versions with disposable collection system (FLOVAC® 1000ml) composed by a reusable polycarbonate

vessel and polyethylene disposable bag (collection liner for fluids suction canisters).

The filter is produced with (PTFE) hydrophobic material to prevent fluids entering the pneumatic circuit. It should be changed

immediately if it becomes wet or if there is any sign of contamination or discolouration. If should also be changed if the unit is used

with a patient whose risk of contamination is unknown. Don't use the suction unit without the protection filter. If the suction

unit is used in an emergency or in a patient where the risk of contamination is not know the filter must be changed after each use.

Available under request with different versions with complete jar 2000ml.

WARNING: Suction tubes for insertion in the human body purchased separately from the machine should comply with ISO

10993-1 standards on material biocompatibility.

WARNING: The medical device is provided without a specific suction probe. If this device must be used with a specific suction

probe, the end user is responsible for making sure it complies with the EN 10079-1 regulation.

Aspiration jar: The mechanical resistance of the component is guaranteed up to 30 cycles of cleaning and sterilization.

Beyond this limit, the physical-chemical characteristics of the plastic material may show signs of decay. Therefore, we recommend

that you to change it.

Silicone tubes: the number of cycles of sterilization and/or cleaning is strictly linked to the employment of the said tube.

Therefore, after each cleaning cycle, it is up to the final user to verify whether the tube is suitable for reuse. The component must

be replaced if there are visible signs of decay of the material constituting the said component.

Conical fitting: the number of cycles of sterilization and the number of cleaning cycles is strictly linked to the employment of the

said component. Therefore, after each cleaning cycle, it is up to the final user to verify whether the fitting is suitable for reuse.

The component must be replaced if there are visible signs of decay in the material constituting the said component.

Service life of the device: More than 1000 hours of operation (or 3 years) in accordance with the standard conditions of testing and

operation. Shelf life: maximum 5 years from the date of manufacture.

Before using the device, the manufacturer advises you to clean and/or sterilize the accessories.

Washing and / or cleaning the autoclavable jar as to be carried out as follows:



Wear protection gloves and apron (glasses and face mask if necessary) to avoid contact with contaminating

substances;



Disconnect the tank from the device and remove the said container from the support of the device.



Separate all the parts of the cover (overflow device, washer).



Disconnect all tubes from the jar and the protection filter



Wash each part of the container from secretions under cold running water and then clean every single part in hot

water (temperature not exceeding 60°C)



Once again, carefully wash each single part using, if necessary, a non-abrasive brush to remove any deposits.

Rinse with hot running water and dry all parts with a soft cloth (non-abrasive). It is possible to wash with commercial

disinfectants by carefully following the instructions and dilution values supplied by the manufacturer.

After cleaning, leave the parts to dry in an open, clean environment.



Dispose of the aspiration catheter according to that provided by local laws and regulations.

The silicone aspiration tubes and the conical fitting may be carefully washed in hot water (temperature must not exceed

60°C). After cleaning, leave the parts to dry in an open, clean environment. When cleaning is complete, reassemble the

container for liquid aspirations according to the following procedure:



Place the overflow valve into its seat in the cover (under VACUUM connector)



Insert floating valve keeping the o-ring towards the opening of the cage



Place the o-ring into its seat around the cover



After completing assembling operations always make sue that cover seals perfectly to avoid vacuum leackages or

liquid exit

ACCESSORIES SUPPLIES

DESCRIPTION

COMPLETE ASPIRATION JAR 1000ml

CONICAL FITTING

TUBES SET 8 mm x 14 mm

HYDROPHOBIC AND ANTIBACTERIAL FILTER

AC/DC ADAPTER

CIGARETTE LIGTHER CABLE