Dentsply Sirona digit Power Dispenser Manuel D'utilisation page 8

digit Power Dispenser performs a self-diagnostic check upon start-up to ensure all systems are functioning properly.
®
1. If the display screen shows an error code (see Graphics description), power the handpiece off by pressing and holding the power/mode selector
button.
2. Ensure the plungers are not fouled or blocked. Remove debris if necessary. Do not attempt to remove debris if plungers are in motion.
3. Attempt to power the handpiece on. If the unit display is normal, the handpiece has self-corrected the error and is fully functional.
4. If ERROR CODE 1: TEMPERATURE is still displayed, unit may be in an overheating condition. Power the handpiece off, and remove handpiece
to a cool, dry area. Allow handpiece to cool for 10 minutes, then power the handpiece on. If the unit display is normal, the handpiece has self-
corrected the error and is fully functional. Avoid exposing handpiece to conditions that caused the overheating.
5. If any error code (including ERROR CODE 1: TEMPERATURE after 10 minute cool-down as described above) is still present, note the code, power
the handpiece off, and contact Dentsply Sirona Technical Support. Do not attempt any further disassembly or remedial actions. Do not attempt
to use the handpiece.
5. Adjusting the Integrated Timer
First Use or to Change Settings
• Display and handpiece default to the "FAST SET" timer and audible signals on first use.
• For subsequent uses, the handpiece will default to the previously used setting.
• If the handpiece is paired with the optional wireless foot control, the Bluetooth icon will display.
• To move between each mode, press and release the power/mode select button.
o FAST SET - (intraoral WORK TIME = 0:35, SET TIME/MRT = 2:30) Corresponding to Aquasil Ultra+ Material Fast Set.
o REG. SET- (intraoral WORK TIME = 1:10, SET TIME/MRT = 5:00) Corresponding to Aquasil Ultra+ Material Regular Set.
o USER SET - User defined WORK TIME and SET TIME/MRT.
In the User Defined mode, the settings may be left to 0:00.
• The handpiece will function normally, with the audible signals disabled.
• The timer counts up from 0:00 showing elapsed time from initial dispensing.
8
• The integrated timer assists in ensuring intraoral placement of impression material is completed within
material intraoral work time.
• The integrated timer automatically counts down the time from first dispensing until the recommended
setting time/mouth removal time (SET TIME /MRT).
• There are three timer modes for digit Power
work and set time notifications. "FAST SET" and "REG. SET" are preprogrammed
to coincide with the work/set times for Aquasil
in digit Power cartridges. "USER SET" allows the user to define work and set time
®
for the material being used.
• User Set - user specifies Work Time and Set Time
1. Scroll by pressing and releasing the power/mode button until the "WORK TIME" displays. "0:00" will be
flashing and the "+ -" adjust icon will appear.
2. Press the forward-located Slow ► to add time or Fast ►► speed buttons to subtract time to set the Work
Time.
3. Press and release the power/mode selection button. "SET TIME" will display. The specified work time from
the step above will be flashing and the "+ -" adjust icon will appear.
Note – pressing and holding either Slow ► or Fast ►► speed buttons will increment or decrement time by
10 seconds respectively.
4. Press the forward-located Slow ► to add time or Fast ►► speed buttons to subtract
time to set the Set Time.
[Notice] – If the User defined Set Time is adjusted to be less than the User defined
Work Time, the timer will disregard the longer user defined Work Time setting and
use the Set Time for both times for audible notifications and automatic plunger retraction .
5. Press and release the power/mode selection button. "USER SET" will display. The time displayed will be the
user defined Set Time from step 4 above.
Dispenser with material
®
Ultra+ Smart Wetting Impression Material
® ®