Publicité
Les langues disponibles
Les langues disponibles
Installation
Serial
Control
control
connections
Digital
output
REMOTE
DIGITAL INPUTS
IN
OUT
LOCAL
DVD
RS232
CONTROL
12V
IN
OUT
TUNER
50/60Hz
TRIGGER
ZONE 2
100–240VAC~
MAX 40VA
LEFT
CENTRE
GROUND
LIFT (IN)
RIGHT
SUB 1
Ground lift
Power supply
Multichannel
connector
POSITIONINGTHE UNIT
Place the processor on a level, firm surface.
Avoid placing the unit in direct sunlight or near sources of heat
or damp.
Do not place the unit on top of a power amplifier or other
source of heat.
Ensure adequate ventilation. Do not place the unit in an enclosed
space such as a bookcase or closed cabinet unless there is good
provision for ventilation.The processor is designed to run warm
during normal operation.
Make sure the IR receiver on the front panel is unobstructed,
otherwise this will impair the use of the remote control. If line-
of-sight is impractical, an infrared remote repeater can be used
with the rear panel IR connector.
Do not place your record deck on top of this unit or any other
unit which is mains supplied. Record decks are very sensitive
to the noise generated by mains power supplies which will be
heard as 'hum' if the record deck is too close.
NOTES ABOUT CONNECTIONS
Before connecting your equipment it is important to think about the
following points as these will affect your choice of connections and
subsequent use of the system.
AUDIO
Wherever possible, connect both analogue and digital outputs of digital
sources. This enables use of a digital input for the main zone and the
corresponding analogue input for recording onto an analogue tape
deck or VCR, and for the zone 2 output if used.
All manuals and user guides at all-guides.com
Digital audio
Component video
inputs
connections
HIGH QUALITY VIDEO
1
Y/
U/
V/
G
B
R
AV
TAPE
CD
VCR
SAT
Y/
U/
V/
G
B
R
OUT
SUB 2
L SURR
LS BACK
LEFT
CENTRE
L SURR
SUB 3
R SURR
RS BACK
RIGHT
SUB
R SURR
OUTPUTS
DVD-A/SACD IN
Multichannel
outputs
DVD-A/SACD
inputs
E-4
Composite & S-video
2
Y/
U/
V/
G
B
R
ZONE 2
2
1
MONITOR OUT
TAPE
VIDEO
TRIGGERS
Y/
U/
V/
G
B
R
1/RGB 2/S-VIDEO
PROG
3
TAPE
LS BACK
TUNER
CD
OUT
RS BACK
ZONE 2 OUT
Zone 2
output
inputs and record
VIDEO
The AV8 does not provide conversion between different video formats
as this would result in degradation of the video signal. This means
simply that the AV8 does not convert between composite, S-video or
component.
For example, if you are watching a composite input from a VCR you
must view it from the composite output of the AV8, as there will be no
picture on the other outputs. Connect as follows:
VCR (composite) input and Monitor out (composite)
or, for a device with an S-video output, such as a DVD player, connect:
DVD (S-video) input and Monitor out (S-video)
The video quality hierarchy is as follows:
Component/RGB – highest
S-video – middle
Composite – lowest
If all the video inputs are simultaneously connected from one device,
e.g., a DVD player, the AV8 will select automatically the best format
possible.
ZONE 2
Zone 2 outputs only a line level signal from the stereo analogue audio
and composite video inputs.The analogue inputs are required because
there is no analogue-to-digital, DSP processing or digital-to-analogue
converstion available for zone 2 signals.
As the AV8 does not convert video formats, a composite video signal
must also be connected from the source.
For this reason, we recommend that source devices that have a digital
connection are also connected to the analogue inputs. High quality
YUV/RGB and S-video sources should also have their composite
outputs connected to the AV8 for use in zone 2.
E-4
connections
VCR
VCR
AV
SAT
DVD
OUT
IN
VCR
IN
OUT
IN
AV
SAT
DVD
AUDIO
Analogue audio
outputs
VIDEO
GND
MM
MC
L
L
R
R
AUX/
PHONO
Publicité
