Operation And Maintenance; Technical Parameters - GRAPHITE 58G022 Traduction De La Notice Originale

• Installation of the drill chuck (1) is similar to removal, only the
sequence of actions is reversed.
• Pull the locking ring (15) away and slide the drill chuck (1) onto
the spindle until you can clearly hear the lock snaps in (it may be
necessary to rotate the drill chuck slightly so it can reach appropriate
position).
INSTALLATION AND REPLACEMENT OF WORKING TOOLS IN THE
SPINDLE HOLDER
• Place appropriate working bit directly in the spindle holder (16) (fig.
G).
• Ensure the bit is inserted to the end and is properly installed.
• To remove the working tool, pull the working bit out of the spindle
holder.
Use additional driver bit adapter with short driver bits. It is
recommended to always make a pilot hole before screwing screws with
the screwdriver. When a short driver bit is installed in the spindle, it is
not necessary to remove it when installing the drill chuck (fig. H).
RIGHT-LEFT DIRECTION OF ROTATION
Choose direction of spindle rotation with the direction selector switch
(5) (fig. I).
Clockwise rotation – set the switch (5) to the extreme left position.
Counter-clockwise rotation – set the switch (5) to the extreme right
position.
* In certain cases position of the switch related to rotation may be different than specified. Please refer to
graphic signs located on the switch or tool body.
Safe position of the direction selector switch (5) is in the middle, it
prevents accidental starting of the power tool.
• Drill cannot be started, when the switch is in this position.
• Use this position of the switch to change drills or bits.
• Before starting the tool make sure the position of the direction
selector switch (5) is correct.
Do not change direction of rotation when the drill spindle is
rotating.
CHANGE OF GEAR
Gear switch (4) (fig. J) allows to increase the range of rotational speed.
Gear I: small speed range, big torque
Gear II: greater speed range, small torque.
Set the gear switch in position appropriate for the works to perform.
When the switch is blocked and cannot be moved, turn the spindle
slightly.
Never change the gear switch position when the drill is operating. It
may damage the power tool.
Long lasting drilling at low rotational speed of the spindle may
cause motor overheating. Make periodic breaks in operation
or allow the tool to operate at top speed without load for
approximately 3 minutes.
HOLDER
The drill provides convenient holder (6) that allows to e.g. hang the tool
on a tool belt when working at heights.

OPERATION AND MAINTENANCE

Remove the battery from the device before commencing any
activities related to installation, adjustment, repair or maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the device with a dry cloth or blow through with compressed
air at low pressure
• Do not use any cleaning agents or solvents, they may damage plastic
parts.
• Clean ventilation holes in the motor casing regularly to prevent
device overheating.
• Always store the tool in a dry place, beyond reach of children.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized by the
manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS
Cordless drill 58G022
Parameter
Battery voltage
Range of idle rotational speed
Range of quick release chuck
Tool holder
Torque control range
Max. torque (soft drive)
Max. torque (hard drive)
Protection class
Weight
Year of production
58G022 defines type and indication of the device
Graphite Energy+ System Battery
Parameter
Battery
Battery voltage
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Graphite Energy+ System Charger
Parameter
Charger type
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Ambient temperature range
Charging time of the battery 58G001
Charging time of the battery 58G004
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure
Sound power
Vibration acceleration
Noise and vibration information
Noise produced by the device is defined with: level of produced sound
pressure Lp and level of sound power Lw
A
uncertainty). Vibrations produced by the device are defined with
vibration acceleration value a
Sound pressure Lp , sound power Lw
A
specified in this manual have been measured in accordance with EN
60745-1:2009+A11:2010. Specified vibration level a
compare tools and for initial evaluation of exposition to vibrations.
Specified vibration level is representative for main applications of the
device. When the device is used for other purposes or with different
working tools, the vibration level may change. Insufficient or too rare
maintenance may increase vibration level. The abovementioned factors
may lead to higher exposure to vibrations during whole working time.
To precisely define exposure to vibrations, include periods when
the device is switched off and when it is switched on but not used
for working. Once all factors have been carefully considered, total
exposition to vibrations may be significantly lower.
To protect the user from results of exposure to vibrations, use additional
safety measures such as: device and working tool periodic maintenance,
proper hand temperature conditions, good work organisation.
12
Value
18 V DC
gear I 0-350 rpm
gear II 0-1250 rpm
0,8 - 10 mm
6,35 mm (¼ '')
1–19 + drilling
28 Nm
44 Nm
III
1,1 kg
2020
Value
58G001 58G004
18 V DC 18 V DC
Li-Ion Li-Ion
2000 mAh 4000 mAh
4 C – 40 C 4 C – 40
0 0 0
1 h 2 h
0,400 kg 0,650 kg
2020 2020
Value
58G002
230 V AC
50 Hz
22 V DC
2300 mA
4 C – 40 C
0 0
1 h
2 h
II
0,300 kg
2020
Lp = 84 dB(A) K= 3 dB(A)
A
Lw = 95 dB(A) K= 3 dB(A)
A
a = 1,552 m/s K= 1,5 m/s
2
h
(where K is measurement
A
(where K is measurement uncertainty).
h
and vibration acceleration ah
A
can be used to
h
C
0
2