Preparation For Operation - GRAPHITE 58G022 Traduction De La Notice Originale

CONSTRUCTION AND USE
Drill is a battery powered tool. Drive consists of a commutator DC
motor with planetary gear. The drill is designed for screwing in and out
screws and bolts in wood, metal, plastics and ceramics, and for drilling
holes in such materials. Quick and tool-free removal of the drill chuck
allows to install single-ended driver bits with different lengths and with
hexagonal shanks, sized 6.35 mm (1/4"), directly on the spindle . An
advantage of the solution is operability in hard to reach areas.
Cordless, battery-powered power tools are especially useful for works in
interior furnishing, adaptation of premises etc.
Use the power tool in accordance with the manufacturer's
instructions only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Quick-release chuck
1.
Ring of the quick release chuck
2.
Torque adjustment ring
3.
Gear switch
4.
Direction selector switch
5.
Holder
6.
Battery
7.
Battery lock button
8.
Switch
9.
Illumination
10.
LED diodes
11.
Charger
12.
Button for battery level indication
13.
Battery level indicator (LEDs)
14.
Locking ring
15.
Spindle
16.
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
angular adapter - 1 pc. (applies to 58G022-AD)
1.
edge adapter - 1 pc. (for 58G022-AD)
2.

PREPARATION FOR OPERATION

REMOVING AND INSERTING THE BATTERY
• Set the direction selector switch (5) in middle position.
• Push the battery lock button (8) and slide out the battery (7)
(fig. A).
• Insert charged battery (7) into the handle holder, you should hear
when the battery lock button (8) snaps.
BATTERY CHARGING
The battery for the device is supplied partially charged. Charge the
battery in ambient temperature between 4°C and 40°C. New battery, or
one that has not been used for a long time, will reach full efficiency after
approximately 3 to 5 charge/discharge cycles.
• Remove the battery (7) from the device (fig. A).
• Connect the charger to mains socket (230 V AC).
• Slide the battery (7) into the charger (12) (fig. B). Make sure the
battery is properly fitted (pushed to the end).
When the charger is connected to a mains socket (230 V AC), the green
diode (11) on the charger turns on to indicate connected supply.
When the battery (7) is placed in the charger (12), the red diode (11) on
the charger turns on to indicate that the charging is in progress.
At the same time green diodes (14) of the battery level indication are
flashing in different configurations, see description below.
• All diodes are flashing - battery is empty and requires charging.
• 2 diodes are flashing - the battery is partially discharged.
• 1 diode is flashing - the battery level is high.
Once the battery is charged, the diode (11) on the charger lights green,
and all battery level diodes (14) light continuously. After some time
(approx. 15 s) battery level indication diodes (14) turn off.
Do not charge the battery for more than 8 hours. Exceeding this time
limit may cause damage to battery cells. The charger does not turn
off automatically when the battery is full. Green diode on the charger
will remain on. Battery level indication diodes turn off after some
time. Disconnect power supply before removing the battery from the
charger socket. Avoid consecutive short chargings. Do not charge the
battery after short use of the tool. Significant decrease of the period
between chargings indicates the battery is worn out and should be
replaced.
Batteries heat up when charging. Do not operate just after charging –
wait for the battery to cool down to room temperature. It will prevent
battery damage.
BATTERY LEVEL INDICATION
The battery is equipped with signalisation of the battery level (3 LED
diodes) (14). To check battery level status, press the button for battery
level indication (13) (fig. C). When all diodes are lit, the battery level is
high. When 2 diodes are on, the battery is partially discharged. When
only one diode is lit, the battery is discharged and must be recharged.
SPINDLE BRAKE
Drill is equipped with electronic brake that stops the spindle
immediately after the switch button (9) is released. The brake ensures
precision when screwing or drilling and prevents free spindle rotation
after switching off.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
Switching on – press the switch button (9).
Switching off – release the switch button (9).
Each time the switch button (9) is pressed, the LED diode (10) lights up
to illuminate the workplace.
ROTATIONAL SPEED CONTROL
Increase or reduce pressure on the switch button (9) to adjust drilling or
driving speed while operating. Speed adjustment allows for a soft start,
which prevents dill slipping when drilling holes in gypsum or glaze, and
allows for operation control when driving screws in and out.
OVERLOAD CLUTCH
Set the torque adjustment ring (3) in appropriate position to
permanently set overload clutch to defined torque value. When the
set torque is reached, overload clutch disconnects automatically. It
prevents from driving screws too deep or damaging the drill.
TORQUE ADJUSTMENT
• Different screws and materials require different torque to be applied.
• The bigger the number corresponding to given position, the bigger
is the torque (fig. D).
• Set the torque adjustment ring (3) to appropriate torque value.
• Always start operation with low torque.
• Increase the torque gradually until obtaining desired results.
• Use higher settings to undo screws.
• When drilling, choose setting marked with the drill symbol. The
torque is the greatest with this setting.
• Knowledge how to choose appropriate torque setting comes with
practice.
Setting the torque adjustment ring in the drilling position
deactivates the overload clutch.
INSTALLATION OF WORKING TOOL IN THE DRILL CHUCK
• Set the direction selector switch (5) in the middle position.
• By turning the ring of the quick release chuck (2) counter clockwise
(see mark on the ring) you can spread jaws enough to insert drill or
driver bit (fig. E).
• To fix the working tool, turn the ring of the quick release chuck (2)
clockwise and tighten firmly.
Deinstallation of the working tool is similar to installation, only the
sequence of actions is reversed.
Make sure the tool position is correct when installing drill or driver
bit in the quick release chuck. Use additional magnetic adapter as an
extension when using short driver bits.
DRILL CHUCK INSTALLATION AND REMOVAL
• Pull the locking ring (15) forward and slide the drill chuck (1) off the
spindle (fig. F).
11