R&G CP0069BL Manuel D'instructions

I
NSTRUCTIONS FOR
Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike
Please note that in cases where kits are packed with rubber washers holding the components onto the bolt – the rubber
washers should be thrown away!
Tops/Fronts – Left/ Right hand side

Remove fairings, undo frame to engine mounting bolt only on one side. The bolt is located high, mid engine.

Unwind bolt until it will touch inner fairing, paint end of bolt with white paint/ Tippex.

Replace fairing, paint mark should then be left on internal side of fairing, remove fairing again, pilot drill
fairing from internal side in centre of white mark, refit fairing and make sure that the pilot hole is in centre of
bolt.

If so, remove fairing using a 28mm tank cutter/cone cutter, carefully drill from external side of fairing to
internal side, deburr hole using sharp knife.

Remove engine bolt completely, insert spacer in the frame cavity, making sure that the hole is in the right
end, refit fairing, then pass bolt through bobbin using two washers under hexagon bolt head and pass through
spacer onto engine. Tighten bolt until you feel some compression from inside the protector. Turn a little
more so that you feel the compression increase slightly. Then apply a quarter turn. Do not overtighten as
damage can occur to the bike. Do not exceed 40nm of torque.

Repeat for opposite side.
Rears/Lowers

Remove engine bolt located just behind the fairing set into frame above crank case, slide the R & G tie bar
through into its location. Remove engine bolt located on the other side and slide bar through.

Slide R & G bobbin over bar on either side, place washers and nuts on bar ends and tighten.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall
at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained
otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These
terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G
Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
Unit 5K, Blacknest Industrial Park, Blacknest Road, Alton, Hampshire, GU34 4PX
Tel: +44 (0)870 220 6380 Fax: +44 (0)1420 521101
CP0069BL & CP0070BL CRASH PROTECTORS
MV A F4 (
GUSTA
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
& S)
FRONT REAR
www.rg-racing.com Email: info@rg-racing.com