Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. CP0402BL
  6. Instructions de montage

R&G CP0402BL Instructions De Montage

Masquer les pouces

Publicité

Liens rapides

Télécharger ce manuel
CP0402
FITTING INSTRUCTIONS FOR CP0402BL
AERO CRASH PROTECTORS FOR KAWASAKI Z300 '15- NON-DRILL KIT
Picture A
Picture B
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of mounting to the
bike.
T
(
).
HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY
FOR CLARITY OF INSTRUCTIONS ONLY
8
3 3
5
6 7
3
6
1
4
2
RIGHT SIDE
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

loading

Manuels Connexes pour R&G CP0402BL

Sommaire des Matières pour R&G CP0402BL

  • Page 1 CP0402 FITTING INSTRUCTIONS FOR CP0402BL AERO CRASH PROTECTORS FOR KAWASAKI Z300 ’15- NON-DRILL KIT Picture A Picture B THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike.

  • Page 2: Left Side

    CP0402 LEFT SIDE LEGEND ITEM 1 = CRASH PROTECTOR CAPS (BC0002) (x2). ITEM 2 = M10 x 1.25 x 160mm LONG HEX HEAD BOLT (x2). ITEM 3 = M10 WASHERS (x6). ITEM 4 = LOCK-WASHERS (LW0001) (x2). ITEM 5 = CRASH PROTECTOR (B0063 with CS066) (x2). ITEM 6 = SPACER (S0952 –...
  • Page 3 CP0402 TOWARDS REAR TOWARDS FRONT OF BIKE OF BIKE PICTURE C GENERAL TORQUE SETTINGS M4 BOLT = 8Nm M5 BOLT = 12Nm M6 BOLT = 15Nm M8 BOLT = 20Nm M10 BOLT = 40Nm Picture 1 Picture 2 Picture 3 Picture 4 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ...
  • Page 4 CP0402 Picture 5 Picture 6 Picture 7 Picture 8 Picture 9 Picture 10 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
  • Page 5 CP0402 Picture 11 Picture 12 Picture 13 Picture 14 Picture 15 Picture 16 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...

  • Page 6: Fitting Instructions

    CP0402 Picture 17 Picture 18 Picture 19 Picture 20 FITTING INSTRUCTIONS Left side (as you sit on the bike)  To fit the R&G crash protectors the side fairing cowls need to be removed from both sides of the bike. ...
  • Page 7 CP0402 disconnected when removing the panel, as shown in picture 10, before gently removing the panel from the bike.  With the side fairing removed from the bike, the two frame mounting bolts can be accessed, as shown in picture 11. ...
  • Page 8 CP0402 PICTURE ‘C’ WITH BIGGER END TOWARD FRONT OF BIKE. Turn a little more so that you feel the compression increase slightly. Then apply a quarter turn. Do not over tighten as damage can occur to the bike. Do not exceed 40N/m of torque. ...
  • Page 9 CP0402 CP0402BL NOTICE DE MONTAGE POUR POUR KAWASAKI Z300 ’15- KIT NON PERCE PROTECTIONS CRASH LATERALES Photo A Photo B E KIT CONTIENT LES ARTICLES EXPOSES CI DESSOUS VERIFIER QUE TOUTES LES PIECES SOIENT PRESENTES AVANT DE PROCEDER AU MONTAGE A FAÇON DONT LE KIT EST EMBALLE NE CORRESPOND PAS FORCEMENT A LA FAÇON DE MONTER...

  • Page 10: Outils Requis

    CP0402 COTE DROIT COTE GAUCHE LEGENDE ARTICLE 1 = CAPUCHONS DE PROTECTION CRASH (BC0002) (x2). ARTICLE 2 = M10 x 1.25 x 160mm BOULONS (x2). ARTICLE 3 = M10 RONDELLES (x6). ARTICLE 4 = RONDELLES DE BLOCAGE (LW0001) (x2). ARTICLE 5 = PROTECTION CRASH (B0063 avec CS066) (x2). ARTICLE 6 = ENTRETOISE (S0952 –...
  • Page 11 CP0402 ARRIERE MOTO AVANT MOTO PHOTO C OUPLES DE SERRAGE RECOMMANDES M4 BOULON = 8Nm M5 BOULON = 12Nm M6 BOULON = 15Nm M8 BOULON = 20Nm M10 BOULON = 40Nm NOTICE DE MONTAGE : Coté gauche (lorsqu’on est assis sur la moto) ...
  • Page 12 CP0402  Glisser une rondelle de blocage (article 4) sur le boulon se façon à ce qu’elle se place contre la rondelle tout juste insérée.  Glisser ensuite le boulon et ses rondelles dans la protection crash (article 5) pour que la tête du boulon et les rondelles se place dans l’alésage, voir photo 16.
  • Page 13 CP0402 representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed.