R&G CP0008BL Instructions De Montage

Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike
Please note that in cases where kits are packed with rubber washers holding the components onto the bolt –
the rubber washers should be thrown away!

Remove fairing

Place offside (throttle side) aluminium fairing bracket (note: components are marked "offside" and "nearside" against
triangle side of frame

Using the two clamps and the four bolts supplied, secure bracket to frame

Install tension bar and repeat above procedure on opposite side

Insert suitable marking tool to enable an impression to be made on the inside of the fairing

Replace fairing panel to obtain mark (suggest Tippex or paint)

Remove fairing panel

Using a 28mm hole saw/cone cutter, drill pilot hole only

Replace fairing to check alignment

Remove panel. Hold the panel securely, pick up on pilot hole and drill slowly with 25mm hole saw (note the panel must be
drilled from the outside towards the inside)

Repeat on the other side

Replace fairings

Install bolt through crash protectors

Slide protector neck through the new fairing hole

Secure tightly (suggest Locktite on bolt)

Tighten bolt until you feel some compression from inside the protector. Turn a little more so that you feel the compression
increase slightly. Then apply a quarter turn. Do not overtighten as damage can occur to the bike. Do not exceed 40nm of
torque.
NOTE: if you are in doubt, please look at our web site
Due to the risk of cross-threading of bolts etc; we recommend that our products be fitted by one of our official dealers or a qualified mechanic.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do
not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no
representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and
the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the
Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been
disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any
defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if
the defect arises from accident or neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned.
These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased
direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the
opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at
time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase.
This policy does not affect your statutory rights and does not refer to faulty goods.
Unit 5K, Blacknest Industrial Park, Blacknest Road, Alton, Hampshire, GU34 4PX
Tel: +44 (0)870 220 6380 Fax: +44 (0)1420 521101
Fitting Instructions for CP0008BL Crash Protectors
Ducati 748, 916 and 996 (not R versions) up to 2001
www.rg-racing.com
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
for the pictures
www.rg-racing.com Email: info@rg-racing.com