Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Specifi cations
Cat.
Volts
No Load
Blade
No.
DC
RPM
0730-20
28
4200
6-1/2"
FUNCTIONAL DESCRIPTION
1.
Front handle
2.
Lock-off button
3.
Trigger
4.
Handle
5.
Battery release buttons
6.
Battery pack
7.
Shoe
8.
Lower guard lever
9.
Lower guard
10. Blade bolt
11. Blade fl ange
12. Blade
13. Wrench
14. Bevel pointer
15. Bevel adjusting knob
16. Bevel scale
17. Rip fence adjusting knob
18. Depth adjusting lever
13
18
Depth of Cut
Depth of Cut
Size
Arbor
At 90°
at 45°
5/8"
0 to 2-1/8"
0 to 1-9/16"
3
4
2
1
9
12
11
10
19. Upper guard
20. Rip fence slot
15
14
21. Sight line
22. Spindle lock button
16
17
22
6
WARNING
charger specifi ed for the battery. For specifi c
charging instructions, read the operator's
manual supplied with your charger and
battery.
WARNING
remove battery pack before changing or re-
5
6
moving accessories. Only use accessories
specifi cally recommended for this tool. Others
may be hazardous.
Removing Battery Pack from Tool
Push in the release buttons and pull the battery
pack away from the tool.
Inserting Battery Pack into Tool
To insert the battery pack onto the tool, slide the
pack onto the body of the tool. Make sure it latches
securely into place.
Fig. 1
7
8
Inserting a
battery pack
Selecting Blade
Always use sharp blades. Dull blades tend to
overload the tool and increase the chance of
KICKBACK (see "Causes and Operator Prevention
of KICKBACK"). Only use thin kerf blades with a
maximum safe operating speed greater than the no
load RPM marked on the tool's nameplate. Read
19
the blade manufacturer's instructions before use.
Do not use any type of abrasive cut-off wheel or
dry diamond cutting blades.
20
Installing and Removing Blades
21
1. R E M O V E B AT T E R Y PA C K B E F O R E
INSTALLING OR REMOVING BLADES.
2. Place the saw on a fl at surface with the blade
facing upwards. To remove the bolt from the
spindle, push in the spindle lock button. While
holding in the spindle lock button, use the
wrench provided with the tool to turn the bolt
clockwise (Fig. 2). Remove the bolt and blade
fl ange.
ASSEMBLY
Fig. 2
Recharge only with the
Always lock trigger or
3. Slide the lower guard lever up to raise the lower
guard. Remove the blade from the spindle. Al-
ways clean the spindle, upper guard and lower
guard to remove any dirt and sawdust.
NOTE: Do not remove inner blade fl ange. Larger
diameter of inner fl ange (Fig. 3) should face the
blade.
Fig. 3
Inner fl ange
Removing a
4. To install a blade, place the blade on the spindle
battery pack
with the teeth pointing in the same direction as
the arrow on the lower guard (Fig. 4). Release
the lower guard lever.
Fig. 4
5. Place the blade fl ange on the spindle and hand
tighten the bolt.
6. While holding in the spindle lock button, use the
wrench to turn the bolt counterclockwise and
tighten.
Adjusting Depth
1. Remove battery pack.
2. To adjust the depth of the cut, hold the saw by
the handle and loosen the depth adjusting lever
by pushing it down toward the shoe (Fig. 5).
7
Spindle
Bolt
Outer fl ange
Publicité
Table des Matières
