Removing/Inserting The Battery - Milwaukee M18 FUEL Manuel De L'utilisateur

ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always use a side
handle when using this tool. Always brace or
hold securely. Ensure side handle is tightened
securely before each use.
Installing the Side Handle
1. To install the side handle,
loosen the side handle grip
until the hooks are far
enough apart to fit into the
slots on the gear case ring.
Position the side handle on
the top, pointing to the left or
right. Tighten the side han-
dle grip until it is secure.
2. To remove the side handle,
loosen the side handle grip
until the side handle can be
removed. Reposition and
tighten securely.
Always remove battery pack before
WARNING
changing or removing accesso-
ries. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
Installing Bits
Always remove the battery before inserting or remov-
ing bits. Select the proper style and size bit for the job.
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16" off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the
bit.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the counter-
clockwise direction.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem with
the chuck's operation.
To learn more about the ONE-KEY functionality for
this tool, please reference the Quick Start guide in-
cluded with this product or go to milwaukeetool.com/
One-Key. To download the ONE-KEY app, visit the
App Store or Google Play from your smart device.
shields.
1. To use the hammer-drilling
Hooks
2. To use the driving screws mode
Slots
The torque specifications shown here are approximate
values obtained with a fully charged battery pack.
Clutch
Setting
NOTE: Because the settings shown in the table are
only a guide, use a piece of scrap material to test
the different clutch settings before driving screws
into the workpiece.
3. To use the drilling only mode,
4
ONE-KEY™
OPERATION
To reduce the risk of injury, wear
WARNING
safety goggles or glasses with side
Selecting Action
mode (Cat. No. 2706-20 only),
rotate the application selector
collar until the hammer symbol
appears in line with the arrow.
Apply pressure to the bit to en-
gage the hammering mechanism.
NOTE: The number selected on the torque selec-
tor collar has no effect on operation of the drill in
this mode.
NOTE: When using carbide bits, do not use water
to settle dust. Do not attempt to drill through steel
reinforcing rods. This will damage the carbide bits.
rotate the application selector
collar until the drive symbol
appears in line with the arrow.
Then rotate the torque selector
collar until the desired clutch set-
ting appears in line with the arrow.
The adjustable clutch, when properly adjusted, will
slip at a preset torque to prevent driving the screw
too deep into different materials and to prevent
damage to the screw or tool.
in. lbs
1 30
2 35 Small screws in softwood.
3 40
4 45
5 50
Medium screws in softwood or
6 55
small screws in hardwood.
7 60
8 65
9 70
Large screws in softwoods. Me-
10 75
dium screws in hardwood or large
11 80
screws in hardwood with pilot hole.
12 85
13 90
rotate the application selector
collar until the drill symbol
appears in line with the arrow.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in
this mode.
Applications