Maintenance; General; Daily Cleaning; Removing The Rotating Rack - Hatco Flav-R-Savor FSD-1 Manuel D'installation Et D'utilisation

MAINTENANCE

General

The Flav-R-Savor Humidified Holding and Display Cabinets
®
are designed for maximum durability and performance, with
minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts may subject operators of the
equipment to hazardous electrical voltage, resulting in
electrical shock or burn. Genuine Hatco Replacement
Parts are specified to operate safely in the environments
in which they are used. Some aftermarket or generic
replacement parts do not have the characteristics that
will allow them to operate safely in Hatco equipment.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.

Daily Cleaning

To preserve the finish of the Flav-R-Savor Humidified Holding
and Display Cabinets, perform the following cleaning procedure
daily.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring
its appearance and making it susceptible to soil
accumulation.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Remove and wash all food pans.
3. Wipe down all interior and exterior metal surfaces with a
damp cloth. Stubborn stains may be removed with a good
non-abrasive cleaner. Clean hard to reach areas using a
small brush and mild soap.
NOTE: Both the rotating display rack and the stationary rack
are removable for cleaning, if necessary. Refer to the
"Removing the Rotating Rack" procedure in this section
for removal.
4. Clean the glass side panels and door panel(s) using
ordinary glass cleaner and a damp, soft cloth or paper
towel. The side panels are removable for detailed cleaning,
if necessary. Refer to the "Removing the Glass Panels"
procedure in this section for removal.

Removing the Rotating Rack

(Models FSD-1, FSDT-1, FSD-2, FSDT-2)
1. Open the front access door.
2. Pull down the spring-mounted coupling to compress.
3. Tip the rack until the rack shaft clears the motor shaft.
NOTE: Do not remove the bow cotter pin from the rack shaft.
Decompressed
Coupling
Rack
Shaft
Compressed
Coupling
Rack
Shaft
Removing Motorized Display Racks
Replacing the Rotating Rack
1. Insert the rack into the cabinet and place the rack bottom
point in the dimple located at the center of the cabinet floor.
2. Pull down the spring-mounted coupling to compress.
3. Tip the rack to line up the rack shaft with the motor shaft
pin.
4. Decompress the spring-mounted coupling until the
coupling is locked in place with the motor shaft pin.

Removing the Glass Panels

1. Lift the glass panel out of the bottom channel of the
cabinet.
2. Pull the lower edge away from the cabinet.
3. Carefully lower the glass until the top clears the cabinet.
Replacing the Glass Panel
1. Position the glass panel with the top edge under the top
cabinet lip, and raise the glass until it clears the bottom
channel of the cabinet.
2. Move the bottom of the glass towards the cabinet until the
glass rests against the cabinet frame.
3. Carefully lower the glass until it rests in the bottom channel
of the cabinet.
12
English
Motor Shaft
Locked Position
Motor Shaft
Unlocked Position
Form No. FSDM-0119