Parkside PSDS 240 A1 Mode D'emploi D'origine page 9

Masquer les pouces Voir aussi pour PSDS 240 A1:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

14. Disconnect tools
– When not in use, before servicing, and
when changing accessories such as blades,
bits and cutters.
15. Remove adjusting keys and wrenches
– Form the habit of checking to see that keys
and adjusting wrenches are removed from
tool before turning it on.
16. Avoid unintentional starting
– Don't carry plugged-in tool with fi nger on
switch. Be sure switch is off when plugging in.
17. Outdoor use extension cords
– When tool is used outdoors, use only exten-
sion cords intended for use outdoors and so
marked.
18. Stay alert
– Watch what you are doing. Use common
sense. Do not operate tool when you are ti-
red.
19. Check damaged parts
– Before further use of the tool, a guard or
other part that is damaged should be care-
fully checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting,
and any other conditions that may affect its
operation. A guard or other part that is dama-
ged should be properly repaired or replaced
by an authorized service center unless other-
wise indicated elsewhere in this instructions
manual. Have defective switches replaced by
an authorized service center. Do not use tool
if switch does not turn it on and off.
20. Warning
– The use of any other accessory or attach-
ment other than recommended it this ope-
rating instruction or the Einhell catalog may
present a risk of personal injury.
21. Have your tool repared by an expert
– This electric appliance is in accordance with
the relevant safety rules repairing of electric
appliances may be carried out only by ex-
perts otherwise it may cause considerable
danger for the user.
Anl_4466143.indb 9
Anl_4466143.indb 9
GB/IE
22. Connect the dust extraction device
Wherever there are facilities for fi tting a dust
extraction system, make sure it is connected
and used.
General safety regulations and accident
prevention
It is essential that you read the safety regulations
and operating instructions in their entirety and
follow the information contained therein in order
to eliminate the possibility of an accident or po-
tentially dangerous situation from occurring while
working with the machine.
Always check the device, the mains cable
and the plug before using the high-pressure
cleaner. Only operate the tool when it is in
good working order and is not damaged in
any way. Damaged parts have to be repla-
ced immediately by a qualified electrician.
Always pull the power plug out of the socket
outlet before doing any work on the machine,
before changing the grinding tool and whe-
never the machine is not being used.
To prevent damage to the power cable, al-
ways lead the power cable away from the
rear of the machine.
Keep the tools in a safe place and out of the
reach of children.
Use on materials containing asbestos is
prohibited.
Note the corresponding accident prevention re-
gulation (e.g. VBG 1 19 in Germany) issued by the
professional associations in your country.
Use only original replacement parts.
Repairs may only be carried out by a quali-
fied electrician.
The machine may exceed 85 db (A) at the
workplace. The operator will require noise
protection measures and ear muffs if this
is the case. The noise of this electric tool is
measured in accordance with IEC 59 CO 1 1,
IEC 704, DIN 45635 part 21, NFS 31-031
(84/537/EEC).
Ensure that you maintain a steady foothold.
Avoid abnormal working postures.
Do not expose your electric tool to rain. Ne-
ver use electric tools in damp or wet locations
- 9 -
22.04.13 13:12
22.04.13 13:12

Publicité

Table des Matières
loading

Table des Matières