R&G AB0007BK Instructions page 14

le loger à travers la fente de la barre aventure puis glisser l'entretoise avant de 36mm (article 14)
sur le boulon. Utiliser la photo du coté gauche de la 2

Mettre la barre aventure en place (photo 15). L'avant de la barre aventure devrait aussi être loge
sur le connecteur sur l'autre barre, à l'avant de la moto (attention à ce que la barre ne rentre pas
en contact avec le carénage ce qui pourrait causer des dommages à la moto).

Loger les boulons dans les supports cadre/moteur (il y a des entretoises entre le cadre et le
boulon sur les 2 boulons qui peuvent avoir besoin d'être enlevés afin de localiser (ceux-ci
peuvent être facilement accessible par le dessous avec votre main)). Glisser la barre aventure sur
le connecteur et serrer légèrement les 2 boulons.

Insérer le boulon à tête ronde M6 (article 12) par dessous, (photo 16) avant d'installer la rondelle
M6 et l'écrou en nyloc.

Les barres aventure peuvent à présent être serrées en place. Serrer tous les boulons de façon
égale des 2 cotés de la moto (Les 4 supports de cadre/moteur serrés à 40Nm maxi et le support
avant pas plus de 20Nm).

Remonter la protection d'origine de transmission double embrayage/moteur (si enlevée) puis le
contour de radiateur en plastic (si enlevé) et serrer tous les boulons.

Vérifier que les barres soient correctement montées et que les boulons de fixation du sous cadre
avant ont un dégagement en verrouillage complet.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
e
page et la photo 14 comme référence.
Email: info@rg-racing.com