Sound Values And Vibration Values - Stihl FSA 130 R Notice D'emploi

English
Fault LEDs on the
battery
The brushcutter 3 LEDs light
cuts out during up red.
operation.
The runtime of
the brushcutter is
too short.
19 Specifications
19.1 STIHL FSA 130 R Trimmer
– Approved batteries:
• STIHL AR
• STIHL AP together with "AP belt bag with
connecting cable"
– Weight without battery, cutting attachment and
deflector: 3.9 kg
– Length without cutting attachment: 1750 mm
For battery life see www.stihl.com/battery-life.
19.2 Sound Values and Vibration
Values
The K-value for sound pressure levels is 2 dB(A).
K-value for sound power levels is 2 dB(A). The
K-value for vibration level is 2 m/s².
STIHL recommends wearing ear defenders.
Using with a mowing head except PolyCut 28-2
– Sound pressure level L
to EN 50636‑2‑91: 83 dB(A)
– Sound power level L
EN 50636-2-91: 94 dB(A)
– Vibration level a measured according to
hv
EN 50636-2-91
– Control handle: 3.3 m/s²
– Loop handle: 3.5 m/s²
Using with a mowing head PolyCut 28-2
– Sound pressure level L
to EN 50636‑2‑91: 84 dB(A)
– Sound power level L
EN 50636-2-91: 97 dB(A)
42
Cause
Trimmer is too hot.
There is an electrical
fault.
The battery is not fully
charged.
The battery life has
been exceeded.
measured according
pA
measured according to
wA
measured according
pA
measured according to
wA
Remedy
► Pull the connecting cable plug out of the
socket.
► Allow trimmer to cool down.
► Pull connecting cable plug out of the
socket and plug it in again.
► If the brushcutter continues to cut out
during operation: Clean the contacts of
the connecting cable as described in the
STIHL AR battery's user manual or in
the user manual for the "AP belt bag with
connecting cable".
► Switch on the brushcutter.
► Recharge the battery fully as described
in the User Manual for the STIHL
AL 101, 301, 301-4, 500 chargers.
► Replace battery.
– Vibration level a measured according to
hv
EN 50636-2-91
– Control handle: 3.3 m/s²
– Loop handle: 3.5 m/s²
Using with a metal cutting attachment
– Sound pressure level L
to EN 50636‑2‑91: 82 dB(A)
– Sound power level L
EN 50636-2-91: 94 dB(A)
– Vibration level a measured according to
hv
EN 50636-2-91
– Control handle: 2.9 m/s²
– Loop handle: 3.7 m/s²
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
stress. The actual vibration stress has to be esti‐
mated. The times when the electric power tool is
switched off and the times when it is switched on
but running under no load can be taken into
account in the estimate.
For information on compliance with Employers'
Vibration Directive 2002/44/EC see
www.stihl.com/vib.
19.3 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
19 Specifications
measured according
pA
measured according to
wA
0458-725-9621-C