Technical Data; Manufacturer's Warranty - Tools - Hilti WSC 85 Mode D'emploi

ORIGINAL OPERATING INSTRUCTIONS
WSC 85 hand-held circular saw
1 Cutting depth adjusting lever
2 Angle adjustment clamping screw
3 Parallel guide clamping screw
4 Cutting line indicator
5 Parallel guide
6 Baseplate
7 Inner clamping flange
8 Spindle
9 Riving knife
10 Spindle lockbutton
11 Screw
12 Clamping flange
13 Pivoting guard
14 Riving knife fastening screws

Manufacturer's warranty - tools

Please contact your local Hilti representative if you have questions about the warranty
conditions.
NOTE
The vibration emission level given in this information sheet has been measured in
accordance with a standardised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary assessment of exposure. The
declared vibration emission level represents the main applications of the tool. However if
the tool is used for different applications, with different accessories or poorly
maintained, the vibration emission may differ. This may significantly increase the
exposure level over the total working period. An estimation of the level of exposure to
vibration should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce the exposure
level over the total working period. Identify additional safety measures to protect the
operator from the effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
Printed: 14.05.2014 | Doc-Nr: PUB / 5071333 / 000 / 02
All manuals and user guides at all-guides.com
15 Extraction system adapter
16 Chip ejector
17 Switch-on interlock
18 On/off switch
19 Hexagon socket wrench
20 Ventilation slots
21 Cutting angle scale
22 Cutting depth scale
23 Cutting depth locking device
24 Auxiliary grip
The accompanying list of safety precautions
and the applicable regulations issued by your
trade association must be observed.

Technical data

Power input:
Power output:
Spindle speed under no load:
Spindle speed under load:
Blade peripheral speed under no load:
Blade peripheral speed under load:
Cutting depth at 0°:
Cutting depth at 45°:
Cutting depth at 60°:
Angular adjustment:
Maximum saw blade diameter:
Minimum saw blade diameter:
Blade mounting hole diameter:
Riving knife thickness (standard):
Dust extraction connector internal dia.:
Weight as per EPTA-Procedure 01/2003:
Protection class as per EN 60745
Noise and vibration information (measured in accordance with EN 60745):
Typical A-weighted sound power level
Typical A-weighted emission sound pressure level
For the given sound power level as per EN 60745, the tolerance is 3 dB.
Wear ear protection!
Triaxial vibration value (vibration vector sum)
Cutting wood (a )
h
Uncertainty (K) for triaxial vibration value
Right of technical changes reserved
User information as per EN 61000-3-11
Switching operations cause short voltage drops. If the mains electric supply conditions
are unfavourable, other tools / machines can be impaired. If the main electric supply
impedance is less than 0.15 Ohms, no disruptions / disturbances need be expected.
1800 W (220–240 V); 1650 W (110 V)
1260 W (220–240 V)
4500/min.
3100/min.
54 m/sec.
37.3 m/sec.
0 to 85 mm
0 to 60 mm
0 to 43 mm
0° to 60°
230 mm
207 mm
30 mm
2.0 mm
35 mm
7.8 kg
Z / II
111 dB (A)
100 dB (A)
2.5 m/s
1.5 m/s
2
2
11