DeWalt DWE496 Traduction De La Notice D'instructions Originale page 9

1 Guard
1 Side handle
1 Flange set
1 Two-pin spanner
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code , which also includes the year of manufacture,
24
is printed into the housing.
Example:
Year of Manufacture
Description (Fig. A, D)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
On/off trigger
1
Lock-off button (B5, ZA models only)
2
Spindle lock
3
Spindle
4
Guard
5
Guard screw
6
Side handle
7
Lock-on button
8
Two-pin spanner
9
Backing flange
10
Threaded clamp nut
11
Intended Use
Your heavy-duty angle grinder has been designed for
professional grinding, sanding, wire brush and cutting.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These heavy-duty angle grinders are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
2017 XX XX
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Attaching Side Handle (Fig. B)

WARNING: Before using the tool, check that the handle is
tightened securely.

WARNING: The side handle should always be used to
maintain control of the tool at all times.
Screw the side handle 7 tightly into one of the holes
either side of the gear case.
Mounting and Removing a Keyed Guard
(Fig. A, C)

CAUTION: Guards must be used with this grinder.
When using the grinder for cutting metal or masonry a Type 1
guard MUST be used. Type 1 guards are available at extra cost
from D WALT distributors.
e
DO nOT use cutting functioning without a proper Type 1 guard.
Misuse may result in serious injury.
nOTE: Please refer to the Grinding and Cutting Accessory
Chart at the end of this section to show other accessories that
can be used with these grinders.
1. Place the angle grinder on a table, spindle
2. Align the lugs with the notches
14
3. Press the guard down and rotate it to the
5
required position.
4. Securely tighten the screw
5. To remove the guard, slacken the screw.

CAUTION: If the guard cannot be tightened by the
adjusting screw, do not use the tool. To reduce the risk of
personal injury, take the tool and guard to a service center
to repair or replace the guard.
Fitting and Removing a Grinding or Cutting
Disc (Fig. A, D, E)

WARNING: Do not use a damaged disc.
1. Place the tool on a table, guard up.
2. Fit the backing flange 10
(Fig. D).
3. Place the disc 17 on the backing flange
fitting a disc with a raised centre, make sure that the raised
centre 16 is facing the backing flange
4. Screw the threaded clamp nut
(Fig. E):
English
13
up.
4
.
15
6 .
correctly onto the spindle 4
10 (Fig. E). When
10 .
11 onto the spindle 4
on
7