EINHELL 36.533.00 Instructions De Montage page 5

Anleitung_Stegplatten_SPK7:_
page 32
20/h
Fasten the hinge strip (Item 6) to the lock catch (Item 5). The an-
gled side of the lock catch must point away from the hinge strip.
20/i
Fit the lock catch to the door profile.
page 33
Reference diagram double door (right and left door wing)
Note: The left figure shows the right door wing from the inside and
the right figure shows the left door wing from the inside.
page 34
21. Assembly of the double door
21/a External wing (left and right door wing)
Place the two door wings on the door hinges of the front wall and
align so that they can engage precisely in each other (see detail
21/b).
page 35
21/b Detail view (outside)
21/c External view (right door wing)
21/b Detail view outside (lock catch)
Align the lock catch on the left door wing so that it fits through the
recess on the rabbet profile of the right door wing.
The greenhouse can be locked with a padlock on the lock catch.
page 36
22. Fitting the door latch
Left door latch (viewed from the outside)
22/a Preassembly preview of the left door latch
Note: First completely assemble the left door latch. It consists of
two door latches (Item 6) which are fastened to the turning strip
(Item 4) with pan-head cylindrical screws (Item 9).
page 37
22/b Turning strip with door latches
The angled ends of the door latches must point upwards (Figure
22/a).
22/c External view (left door wing)
Fasten the bush (Item 3) for the door latch to the outside of the
door. If necessary pre-drill fastening holes with a cordless screw-
driver.
page 38
22/d Preassembly of the T-handle
22/e External view (left door wing)
17.02.2009 16:39 Uhr Seite 5
page 39
22/f Internal view (left door wing)
Important note: The individual screw preassembled in step 20/b
in the top guide rail of the door center profile must be positioned
between the turning strip and the side door profile. This screw
serves as the end stop for the turning strip and must therefore be
tightened directly next to it.
22/g Internal view (left door wing)
page 40
22/h Internal view (door, top)
22/i Internal view (door, bottom)
Fasten the rods of the door latch to the door profiles using a
spacer plate (Item 5) in each case and a guide plate at the front
(Item 8). Use the hexagon head screws preassembled in step 20 in
the top and bottom door profile.
page 41
22/j Internal view (door, top)
Internal view (door center, door latch)
Internal view (door, bottom)
When the door handle is in a horizontal position, the door is
closed.
Note: If the door does not close correctly or the rods catch slightly
when the door is opened, undo the screws on the door hinges and
align the height of the door wings precisely.
page 42
Right door latch (viewed from the outside)
Note: Repeat steps 22/b to 22/i, however in addition fit the latch to
the side of the top door latch (Item 4).
page 43
Preassembly of the side latch at the right door latch
The angled end of the latch faces upwards.
22/m Internal view (right door wing)
Note: The side latch will slide in front of the door profile of the
other door wing as soon as the handle is turned.
page 44
23. Preassembly of the door window
Important note: This step describes the assembly of the right-
hand door window. Repeat this step for the left-hand door window
– remembering that the left-hand door window is fitted the oppo-
site way round.
Important note – take care not to mix up the components:
The profiles "horizontal EP window profile" and "horizontal win-
dow profile" differ in shape only as a result of the two notches at
the ends. Please refer to the following figures:
84.082.37 Horizontal EP window profile (with slots)
84.082.31 Horizontal window profile (without slots)
GB
5