DeWalt DCS571 Traduction De La Notice D'instructions Originale page 41

Blades

WARNING: To minimize the risk of eye injury, always
use eye protection. Carbide is a hard but brittle
material. Foreign objects in the workpiece such as wire or
nails can cause tips to crack or break. Only operate saw
when proper saw blade guard is in place. Mount blade
securely in proper rotation before using, and always use a
clean, sharp blade.

WARNING: Do not cut ferrous metals (steel), masonry,
glass, masonry-type planking, cement board or tile with
this saw.
Do not use abrasive wheels or blades. A dull blade will cause
slow inefficient cutting, overload on the saw motor, excessive
splintering, and could increase the possibility of kickback.
If you need assistance regarding blades, please contact your
local service center listed on the back of the manual.
Blade Diameter
DWA412TCT 115 mm
DWA412PCD 115 mm
Prior to Operation
• Make sure your battery pack is (fully) charged.
• Make sure the guards have been mounted correctly. The
saw blade guard must be in closed position.
• Make sure the saw blade rotates in the direction of the
arrow on the blade.
• Do not use excessively worn saw blades.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Always wear proper personal hearing
protection. Under some conditions and duration of use,
noise from this product may contribute to hearing loss.
Instructions for Use

WARNING:
• Ensure the material to be sawn is secured in place.
• Apply only a gentle pressure to the tool and do not
exert side pressure on the saw blade. If possible, work
with the saw shoe pressed against the workpiece. This
prevents damage to the blade and stops the tool from
jerking and vibrating.
• Avoid overloading.
• Let the blade run freely for a few seconds before
starting the cut.
Teeth Application
24 Wood cutting
4 Fibre cement cutting
Proper Hand Position (Fig. H)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
or, if the auxiliary handle is attached, one hand on the main
21
handle and one hand on the auxiliary handle
Switching On and Off (Fig. A)
For safety reasons the trigger switch
1
with a lock‑off button .
Press the lock‑off button to unlock the tool.
To run the tool, press the trigger switch
trigger switch is released the lock‑off switch is automatically
activated to prevent unintended starting of the machine.
NOTICE: Do not switch the tool ON or OFF when the saw
blade touches the workpiece or other materials.
Guiding the Tool (Fig. A, I)
• For optimum results, clamp the workpiece bottom up.
9
• Use the kerf indicator
workpiece. The kerf indicator lines up with the left side of
the saw blade when set to 45 ° bevel. The kerf indicator lines
up with the right side of the saw blade when set to 0 ° bevel.
• To adjust the kerf indicator
28
screw with the hex key
or right as needed. Tighten screw when finished adjusting
the indicator.
Dust Extraction (Fig. I–K)

WARNING: Risk of dust inhalation. To reduce the risk of
personal injury, ALWAYS wear an approved dust mask.

WARNING: ALWAYS use a dust class M vacuum extractor
designed in compliance with the applicable directives
regarding dust emission when cutting hazardous dust.
24
The dust extraction port
to an external dust extractor, either using the AirLock system,
or a standard 35 mm dust extractor fitment. The AirLock
22
connector connects directly to D
and extractors.
Attach the dust extraction port
the dust extraction mounting port
until secure. The dust collection port is adjustable through
180 degrees.
1. Ensure the collar on the AirLock connector is in the unlock
position. (Refer to Figure J.) Align notches
AirLock connector as shown for unlock and lock positions.
2. Push the AirLock connector onto the dust
24
extraction port .
3. Rotate the collar to the locked position.
nOTE: The ball bearings inside collar lock into slot and
secure the connection.The power tool is now securely
connected to the dust extractor.
EnGLIsh
12
.
2
of your tool is equipped
2
. As soon as the
to follow the line drawn on the
9
, loosen the kerf indicator
14
and move the indicator left
allows you to connect the tool
WALT compatable tools
e
24
to the saw by sliding it onto
31
using a twisting motion
23
on collar and
21
39