DeWalt DCS571 Traduction De La Notice D'instructions Originale page 40

EnGLIsh
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
16
button . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Installing the Belt Hook (Fig. C)

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the tool
from a work belt. DO NOT use the belt hook for tethering
or securing the tool to a person or object during use. DO
NOT suspend tool overhead or suspend objects from the
belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
IMPORTanT: When attaching or replacing the belt hook
20
use only the screw that is provided. Be sure to securely
tighten the screw.
If the hook is not desired at all, it can be removed from the tool.
Trigger Switch (Fig. A)

WARNING: This tool has no provision to lock the trigger
switch in the ON position and should never be locked ON
by any other means.
Release the trigger switch lock‑off button
button. Pull the trigger switch
the trigger switch turns the motor off.
Depth of Cut Adjustment (Fig. D)
1. Loosen the depth adjustment lever
5
2. Move the shoe to obtain the correct depth of cut.
3. Tighten the depth adjustment lever
4. For the most efficient cutting action using a carbide tipped
saw blade, set the depth adjustment so that about one half
of a tooth projects below the surface of the wood to be cut.
nOTE: A method of checking for the correct cutting depth
is shown in the inset in Figure D. Lay a piece of the material
you plan to cut along the side of the blade and observe how
much tooth projects beyond the material.
Bevel Adjustment (Fig. E)
The bevel angle can be adjusted between 0 ° and 45 °.
1. Loosen the bevel adjustment knob
2. Set the bevel angle by tilting the saw shoe
indicates the desired angle on the scale.
3. Tighten the bevel adjustment knob
38
1
by pressing the
2
to turn the motor on. Releasing
4
.
4
.
10
.
5
until the mark
10
.
Shoe Adjustment for 90 ° Cuts (Fig. A, D, E)
1. Adjust the saw to 0 ° bevel.
2. Retract the blade guard using the lever
on the blade side.
3. Loosen the bevel adjustment knob
4. Place a square against the blade and shoe to adjust the
90 ° setting.
5. Turn the calibration screw
the proper angle.
6. Confirm the accuracy of the setting by checking the
squareness of an actual cut on a scrap piece of material.
Rip Guide Installation and Usage (Fig. A, F)
Ripping is the process of cutting wider boards into narrow
strips, cutting the grain lengthways. Hand guiding is more
difficult for this type of sawing and the use of the rip guide
is recommended.

WARNING: For your own safety, read the instruction
manual before using any accessory. Failure to heed
these warnings may result in personal injury and serious
damage to the saw and accessory. When servicing this
tool, only use identical replacements.
Assembly
19
,
1. Loosen the rip fence guide locking screw
14
key .
2. Insert the rip guide
3. Tighten the rip fence guide locking screw
Use the supplied rip guide only with the DCS571 circular
saw. Use of this rip guide with other saws may increase the risk
of kickback and injury.
Before making a cut, ensure the rip fence is securely fastened
to the tool.
After installing the rip guide on the saw or after moving the
guide to change the rip width setting, check the operation
of the lower guard before starting the saw and making a
cut to make sure that the rip guide does not affect proper
guard operation.
Replacing the Saw Blade (Fig. A, G)
1. Engage the blade lock button
clamping screw
supplied with the tool.
2. Retract the lower blade guard
replace the blade. Reinstall the washers (
correct position.
3. Check the direction of rotation of the blade.
4. Thread on the blade clamping screw
washer in position. Turn counterclockwise.
5. Press the blade lock button
until the blade stops rotating.
6. Tighten the blade clamping screw firmly using the hex key.
6
and place the saw
10
.
29
so that the shoe will stop at
27
30
as shown in Figure F.
27
11
and unscrew the blade
8
by turning clockwise using the hex key
7
using the lever
17
8
by hand to hold the
11
while turning the spindle
with the hex
securely.
6
and
18
, ) in the