Installation; Television Location; Optional Cable Connections; Ac Power Supply Cord - Panasonic CT-30WC14 Manuel D'utilisation

Installation

Television Location

This unit can be used as part of an entertainment center.
your dealer for available options.
• Avoid excessive sunlight or bright lights, including
reflections.
• Keep away from excessive heat or moisture. Inadequate
ventilation may cause internal component failure.
• Fluorescent lighting
transmitting range.
• Keep away from magnetic equipment, including motors,
fans and external speakers.
WARNING: Use this television receiver only with the
cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart
is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over. In order to
avoid injury to children, never place your television receiver on a
piece of furniture that is capable of being tilted by a child leaning
on it, pulling on it, standing on it, or climbing on it. A falling
television can cause serious injury or even death.
CT-30WC14, CT-30WC14U:
CAUTION: These television receivers for use only with
PANASONIC TY-30WX54T stand. Use with other carts
(or stands) is capable of resulting in instability causing
possible injury.
CT-30WX54, CT-30WX54U:
CAUTION: This television receiver for use only with
PANASONIC TY-30WX54T stand. Use with other carts
(or stands) is capable of resulting in instability causing
possible injury.
CT-34WX54, CT-34WX54U:
CAUTION: This television receiver for use only with
PANASONIC TY-34WX54T stand. Use with other carts
(or stands) is capable of resulting in instability causing
possible injury.

Optional Cable Connections

Shielded audio and video cables should be used between
components. For best results:
• Use 75-ohm coaxial shielded cables.
• Use appropriate input and output connectors, that match
your component connectors.
• Avoid long cables to minimize interference.

AC Power Supply Cord

CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT
OF AC OUTLET AND FULLY INSERT. DO NOT
USE A PLUG WITH A RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADE CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
PROTECT POWER CORDS FROM BEING WALKED ON, ROLLED
OVER, CRIMPED, BENT, OR PINCHED, PARTICULARLY AT PLUGS,
CONVENIENCE RECEPTACLES, AND THE POINT WHERE THEY EXIT
FROM THE APPARATUS.
Consult
may reduce remote control
Polarized plug

Cable / Antenna Connection

For proper reception, either a cable or antenna connection
is required.
Cable Connection
Connect the cable supplied by your local
cable company. Tighten with fingers only.
Use of any tool (e.g. pliers) for tightening
may result in tuner damage.
Note: A cable converter box may be
required for proper
Check with your
company for compatibility requirements.
Antenna Connection
For proper reception of VHF/UHF channels, an external antenna
is required. For best reception an outdoor antenna is
recommended.
• Connect home antenna to ANT
connection on back of television.
Note: Cable Mode is preset at the
factory.

Remote Control Battery Installation

Requires two AA batteries (supplied)
1
Procedure
1. Turn the remote control face down. Remove battery
cover by pressing down on the marking on the cover
and sliding it off in the direction indicated.
2. Install batteries matching (+) and (-) polarity signs.
3. Replace the battery cover by sliding in reverse until the
lock snaps.
Note: Incorrect installation can cause battery leakage and
corrosion that will damage the Remote Control.
Precautions
• Replace batteries in pairs.
• Do not mix battery types (zinc carbon with alkaline).
• Do not recharge, heat, short-circuit, disassemble, or
burn batteries.
I
NSTALLATION
Incoming Cable from
Cable Company
75 Ohm VHF/UHF
on back of TV
reception.
local cable
Incoming Cable from
Home Antenna
.
5