Worx WG160 Mode D'emploi page 11

permit charging. Allow time for the battery to
cool down before recharging.
3. To REmovE oR iNSTall BaTTERy
PaCk (See Fig. C)
Depress the battery release button to remove
Battery Pack (2) from your trimmer. After
recharging, insert the Battery Pack onto
trimmer's battery bracket. A simple push and
slight pressure will be sufficient.
4. SaFETy oN/oFF SwiTCH (See Fig. d)
The safety switch is locked off to prevent
accidental starting. Depress the Lock Off
Button (9) then depress the On/Off Switch (10)
and release Lock Off Button. Your trimmer is
now on. To switch off, just release the on/off
switch.
waRNiNG! The cutting head
continues to rotate after the
trimmer has been switched off; wait until
it has completely stopped then lay down
the tool.
5. adjuSTmENT oF THE TElESCoPiC
SHaFT (See Fig. E)
Step one foot on the Safety Guard, then
use one hand to pull up the Telescopic Shaft
Adjustment Trigger (8), adjust the length of
the Telescopic Shaft to the most comfortable
length. Release the Telescopic Shaft.
Adjustment Trigger to lock in position.
6. maiN HaNdlE RoTaTioN
(See Fig. F1, F2)
First, hold down the lower housing with your
foot and pull upward on the Upper Shaft (15).
Then rotate the Upper Shaft clockwise 90
degrees (See Fig. F1) and release; the Shaft
will be locked in position automatically (See
Fig. F2).
7. adjuSTmENT oF auxiliaRy HaNdlE
Pull up the Auxiliary Handle Locking Lever (11).
Hold the Locking Lever and rotate the Auxiliary
Handle to the most comfortable and balanced
position (See Fig. G)
Release the lever, your Auxiliary Handle has
been locked.
3 in 1 Grass Trimmer/Edger
8. adjuSTmENT oF THE TRimmER
HEad aNGlE To THE SHaFT
(See Fig. H1, H2 & H3)
waRNiNG: make Sure the Safety
Switch is locked off to Prevent
accidental Starting.
To adjust the Upper Shaft angle or convert the
tool from trimming mode and edging mode,
unlock the Pivot Head Locking Knob by hand,
and using adequate force, pull the trimmer
head into the desired position, then lock the
Pivot Head Locking Knob.
9. FlowER GuaRd/EdGER GuidE
Pull the Flower Guard/Edger Guide out before
trimming, as shown in Fig. I1.
When edging, pull Flower Guard/Edger Guide
out also, and keep to a side (See Fig. I2).
Before trimming or edging make sure the
flower guard is locked firmly in position.
oPErATIoN
waRNiNG: Always wear the eye
protection. Never lean over the trimmer
head. Rocks or debris can ricochet or be
thrown into eyes and face and cause
blindness or other serious injury. When
operating unit, check for the following:
Wear eye protection and heavy clothing. Hold
front handle with one hand and Auxiliary
Handle with the other hand. Keep unit below
waist level. Work only from your right to your
left to ensure debris is thrown away from you.
Without bending over, keep line near and
parallel to the ground (perpendicular when
edging) and not crowded into material being
cut.
waRNiNG: make sure that line is
fed out before operation. make
sure motor is up to full speed before
trimming or edging.
waRNiNG: Only use 0.065"(1.65mm)
diameter cutting line. Other sizes of line
will not feed properly and will result in
improper cutting head function or can cause
serious injury. Do not use other material such
as wire, string, rope, etc. Wire can break off
during cutting and become a dangerous
projectile that can cause serious injury.
11
EN